Installation - Pioneer AVH-P5750DVD Installation Manual

Installation

When connecting the external video component and the display
RCA cables
External video
(sold separately)
This unit component
(sold separately)
To video output
Video input
Audio input
Video output
Multi-DVD Player
(sold separately)
Video output
To audio outputs
RCA cables
(sold separately)
Audio output
RCA cable
(sold separately)
Display with
RCA input jacks
To video input
• It is necessary to set AV INPUT to VIDEO in SET UP when connecting an external
video component.
• It is necessary to set AV INPUT to M-DVD in SET UP when connecting a multi-DVD
player.
When using a display connected to rear video output
This product's rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
WARNING:
• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while
Driving.
Note: Installing the remote control unit
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected When not using the remote control unit,
up properly, and the unit and the system work
secure it with velcro tape to prevent it
properly.
from moving.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts • Thoroughly wipe off the surface
can cause malfunctions.
before affixing the velcro tape.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• Do not install the display where it may (i) obstruct
the driver's vision, (ii) impair the performance of
any of the vehicle's operating systems or safety
features, including air bags, hazard lamp buttons or
(iii) impair the driver's ability to safely operate the
vehicle.
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot
— for instance, near a heater outlet.
• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 12)
Fig. 11
30°
Fig. 12
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
fires to radiate freely. (Fig. 13)
Do not close this area.
Fig. 13
DIN Front/Rear-mount
This unit can be properly installed
either from "Front" (conventional DIN
Front-mount) or "Rear" (DIN Rear-
mount installation, utilizing threaded
screw holes at the sides of unit chassis).
For details, refer to the following illus-
trated installation methods.
Remote control unit
Before installing the unit
Velcro tape (small)
(hard)
• Remove the frame and the hold-
Velcro tape (small)
er. (Fig. 15)
(soft)
Pull out to remove the frame and then
loosen the screws (2 × 3 mm) to
remove the holder. (When reattaching
the frame, point the side with a groove
downwards and attach it.)
Fig.14
Holder
Screw (2 × 3 mm)
Frame
Fig. 15
DIN Front-mount
Installation with the rubber bush
1. Decide the position of the side
brackets. (Fig. 16)
When installing in a shallow space,
change the position of side brackets. In
this case, stick conceal tape on parts
that protrude from the dashboard.
DIN Rear-mount
Installation using the screw holes on
the side of the unit
• Fastening the unit to the factory
radio mounting bracket. (Fig. 18)
Conceal tape
(Fig. 19) (Fig. 20)
Select a position where the screw holes
Side bracket
of the bracket and the screw holes of
Flush surface screw (5 × 6 mm)
this product become aligned (are fitted),
and tighten the screws at 2 places on
Fig. 16 each side. Use any of binding screws (4
× 3 mm), binding screws (5 × 6 mm) or
2. Install the unit into the dash-
flush surface screws (5 × 6 mm),
board. (Fig. 17)
depending on the shape of the screw
holes in the bracket.
After inserting the holder into the dash-
*1 Use binding screws (4 × 3 mm) only.
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
* 1
* 1
Dashboard
182
Rubber bush
53
Screw • When installing in a shallow space,
use the following screw holes. In this
case, stick conceal tape on parts that
Holder
protrude from the dashboard.
Side bracket
Screw (2 × 3 mm)
* 1
* 1
• After installing the unit into the dash-
board, reattach the frame.
Fig. 17
<ENGLISH>
Screw
Dashboard or
Console
Factory radio mounting
bracket
Fig. 20
Fixing the front panel
If you do not operate the removing and
attaching the front panel function, use
the supplied fixing screws to fix the
front panel to this unit.
• Fix the front panel to the unit
using fixing screws after remov-
ing the front panel. (Fig. 21)
Fig. 18
Fixing screw
Conceal tape
Fig. 21
Fig. 19