Accessories - Viessmann VITOTRONIC 200 Technical Data Manual

Accessories

Note on the room temperature sensing
*1
function (RS function) when using a
remote control
Due to the slow response of the
underfloor heating, the RS function must
not influence the underfloor heating
circuit.
For heating boilers with a low limit, the
RS function must not influence the
heating circuit without a mixing valve.
*1
RS function = remote control with
room sensor function
*2
WS function = remote control only, no
room sensor function
Vitotrol 200,
Part No. 7133 378
The Vitotrol 200 remote control takes
care of the room temperature setpoint
adjustment at normal operation and
determines the heating program from any
given room.
The Vitotrol 200 features illuminated
heating program selector buttons as well
as a party and an economy button.
Fault messages are displayed on the
boiler control.
A remote control can be connected for
each heating circuit.
*2
WS function
: Allows for installation at
any given place in the building.
*1
RS function : The remote control is to
be installed on an inside wall of the main
living area, across from radiators, but not
on shelves, in niches, in the close vicinity
of doors or heat sources of any kind (e.g.
direct sunlight, fireplace, TV, etc.).
The installed sensor measures room
temperature and, if necessary, takes
corrective action and initiates fast
heat-up at the outset of the heating
operation (if coded).
Connection:
2-wire cable, cable length
–
max. 164 ft./50 m (also for the
connection of several remote controls).
The cable must not be placed together
–
with line voltage wiring.
Low voltage plug is included.
–
Rated voltage: 33 VAC
Rated current: 10 mA
Power consumption: 3.3 W
Maximum ambient
temperature
– at operation: 32 to 104 ºF/
0 to 40 ºC
– when storing
or transporting: –4 to+149 ºF/
–20 to +65 ºC
Adjustment range of
room temperature
setpoint: 50 to 86 ºF/
10 to 30 ºC
adjustable to
37 to 73 ºF/
3 to 23 ºC
or
63 to 99 ºF/
17 to 37 ºC
Adjustment of the room temperature
setpoint at reduced operation takes place
at the Vitotronic 200.
Accessories
Vitotrol 300,
Part No. 7133 382
The Vitotrol 300 remote control takes
care of the room temperature setpoint
adjustment at normal and reduced
operation for the heating program,
switching times for room heating,
domestic hot water heating and the
domestic hot water recirculation pump.
The Vitotrol 300 features illuminated
heating program selector buttons, a party
and an economy button, an automatic
reset function to daylight savings time,
buttons for the holiday program, day of
the week and time.
*2
WS function : Allows for installation at
any given place in the building.
*1
RS function : The remote control is to
be installed on an inside wall of the main
living area, across from radiators, but not
on shelves, in niches, in the close vicinity
of doors or heat sources of any kind (e.g.
direct sunlight, fireplace, TV, etc.).
The installed sensor measures room
temperature and, if necessary, takes
corrective action and initiates fast
heat-up at the outset of the heating
operation (if coded).
Connection:
2-wire cable, cable length
–
max. 164 ft./50 m (also for the
connection of several remote controls).
The cable must not be placed together
–
with line voltage wiring.
Low voltage plug is included.
–
Rated voltage: 33 VAC
Rated current: 10 mA
Power consumption: 3.3 W
Maximum ambient
temperature
– at operation: 32 to 104 ºF/
0 to 40 ºC
– when storing
or transporting: –4 to +149 ºF/
–20 to +65 ºC
Adjustment range of
room temp. setpoint:
– at normal operation: 50 to 86 ºF/
10 to 30 ºC
adjustable to
37 to 73 ºF/
3 to 23 ºC
or
63 to 99 ºF/
17 to 37 ºC
– at reduced operation: 37 to 99 ºF/
3 to 37 ºC
5