Alcatel-lucent ip communication products brochure (2 pages)
Summary of Contents for Alcatel-Lucent SFP
Page 1
060220-00 Rev. M April 2011 OmniSwitch Transceivers Guide www.alcatel-lucent.com...
Page 2
. The information described in this guide is subject to change without notice. Attention : Use of any transceivers other than those part numbers listed in the SFP and XFP Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for proper performance and may result in voiding the warranty for the affected platforms.
OmniSwitch SFP and XFP transceivers for all OmniSwitch AOS 6 Release Products. Attention : Use of any transceivers other than those part numbers listed in the SFP and XFP Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for proper performance and may result in voiding the warranty for the affected platforms.
Who Should Read this Manual? The audience for this user guide is network administrators and IT support personnel who need to provide network connectivity using SFP or XFP transceivers on an OmniSwitch. When Should I Read this Manual? Read this guide as soon as you are ready to integrate your OmniSwitch into your network and you are ready to provide connectivity using the supported transceivers.
How is the Information Organized? How is the Information Organized? Chapters in this guide are broken down by transceiver type, SFP or XPF. Additional sub-sections are provided for the various types of transceivers. Specification Information. Each transceiver has an associated table providing individual specifications for all supported transceivers.
Page 8
Documentation Roadmap About This Guide Stage 3: Integrating the Switch Into a Network Pertinent Documentation: Network Configuration Guide Advanced Routing Configuration Guide When you are ready to connect your switch to the network, you will need to learn how the OmniSwitch implements fundamental software features, such as 802.1Q, VLANs, Spanning Tree, and network routing protocols.
About This Guide Related Documentation Related Documentation The following are the titles and descriptions of all the related OmniSwitch AOS Release 6 user manuals: • OmniSwitch 6250 Series Getting Started Guide Describes the basic information you need to unpack and identify the components of your OmniSwitch 6250 shipment.
Page 10
Chapters cover multicast routing (DVMRP and PIM-SM), and OSPF. • OmniSwitch Transceivers Guide Includes SFP and XFP transceiver specifications and product compatibility information. • Technical Tips, Field Notices Includes information published by Alcatel-Lucent’s Customer Support group.
Support web page, you’ll be able to view and update any case (open or closed) that you have reported to Alcatel-Lucent’s technical support, open a new case or access helpful release notes, technical bulletins, and manuals. For more information on Alcatel-Lucent’s Service Programs, see our web page at service.esd.alcatel-lucent.com, call us at 1-800-995-2696, or email us at esd.support@alcatel-lucent.com.
Page 12
Technical Support About This Guide page xii OmniSwitch Transceivers Guide April 2011...
OmniSwitch Series switches use both copper-based and fiber-based optical Small Form Factor Pluggable (SFP) transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach applications. Copper-based and fiber-based optical SFPs can be mixed on the same module.
The Small Form-Factor Pluggable (SFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. The SFP connector consists of a 20-pin receptacle and an SFP housing cage. The connector provides the interface for the hot pluggable SFP module. Each SFP module contains a serial interface to provide identification information that describes the SFP capabilities, stand interfaces, manufacturer and other information.
(provided) when the SFP is not in use. Eye Safety: SFP transceivers are international Class 1 laser products and are eye-safe devices when oper- ated within the limits of manufacturers’ specifications. Operating SFP transceivers in a manner inconsis- tent with intended usage and specification may result in hazardous radiation exposure.
Page 16
SFP Transceiver Installation and Removal Small Form-Factor Pluggables (SFPs) To install, align the transceiver with the transceiver slot on the NI module, as shown. Be sure that the bail wire delatch is in the up, or closed position. Slide the transceiver straight into the slot until the module clicks firmly into place.
Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers SFP-100-BX20LT Bi-Directional SFP Optical Transceiver. Connector Type Standards Supported 802.3ah, SFP MSA, ITU-T G.983 Connections Supported 100Base-BX Fiber Type Wavelength Transmit: 1550 mm Receive: 1310 nm Average Power Output -14 to -8 dBm...
Page 22
Bi-directional Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers (cont.) SFP-100-BXLC-D Bi-Directional SFP Optical Transceiver. Connector Type Standards Supported 802.3ah, SFP MSA, ITU-T G.983 Connections Supported 100Base-BX Fiber Type Wavelength Transmit: 1550 mm Receive: 1310 nm Average Power Output...
Page 23
-19.5 dBm Transmission Distance ~10 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-GIG-BX-U SFP-GIG-BX-U Bi-Directional SFP Optical Transceiver. Connector Type Standards Supported 802.3ah, SFP MSA Connections Supported 1000Base-BX10 Fiber Type...
100 FX Ethernet Transceivers Small Form-Factor Pluggables (SFPs) 100 FX Ethernet Transceivers SFP-100-LC-MM SFP Optical Transceiver. Connector Type Standards Supported 802.3u, SFP MSA Connections supported 100Base-FX Fiber Type Wavelength 1310 nm Optical Power Output -19 to -14 dBm on 62.5/125µm -22 to -14 dBm on 50/125µm...
Page 25
Small Form-Factor Pluggables (SFPs) 100 FX Ethernet Transceivers 100 FX Ethernet Transceivers (cont.) SFP-100-LC-SM40 SFP Optical Transceiver. Connector Type Standards Supported 802.3u, SFP MSA Connections Supported 100Base-FX Fiber Type Wavelength 1310 nm Optical Power Output -15 to -8 dBm Receiver Sensitivity...
SFP-GIG-CWD Coarse Wavelength Division Multiplexing (CWDM) is an optical transceiver supporting single-mode fiber over various wavelengths. CWDMs are hot-pluggable and are available for long-reach applications. Connector Type Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-LX Fiber Type Wavelength 1470, 1490, 1510, 1530, 1550, 1570, 1590, 1610...
OmniSwitch Series switches use both copper-based and fiber-based optical Industrial Small Form Factor Pluggable (SFP) transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach applications. Additionally, Industrial SFPs are designed to operate at an increased temperature range of -40 ºC to 85 ºC.
-10.3 dBm Transmission Distance ~ 10 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Supported iSFP-10G-C 10-Gigabit SFP+ Copper Direct Attached Copper Cable. Connector Type Direct Attached Standards Supported 802.3ae Cable Length 30cm, 3m, 10m Digital Diagnostic Monitoring...
3 10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Small Form Factor Pluggables (XFPs) are fiber-based optical transceivers. XFPs are fully hot- swappable and are available for both short-reach and long-reach applications. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported XFP transceivers. For additional details about OmniSwitch modules, see the appropriate OmniSwitch Hardware Guide.
10-Gigabit Small Form Factor Pluggables (XFPs) XFP MSA Specification XFP MSA Specification The 10-Gigabit Small Form-Factor Pluggable (XFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. The XFP connector consists of a 30-pin receptacle and an XFP housing cage.
XFP Transceiver Installation and Removal 10-Gigabit Small Form Factor Pluggables (XFPs) XFP Transceiver Installation and Removal Follow the instructions below when installing an XFP transceiver. ESD Caution: Before handling the module, you must discharge all static electricity on your person to avoid Electrostatic Discharge (ESD) damage.
4 SFP Compatibility Matrix OmniSwitch 9000 Series The following table shows the Ethernet transceiver configurations and minimum release required for support on the OmniSwitch 9000 Series: OS9-GNI-C20L OS9-GNI-U24 SFP-GIG-SX 6.1.5 SFP-GIG-LX 6.1.5 SFP-GIG-LH40 6.1.5 SFP-GIG-LH70 6.1.5 SFP-GIG-EXTND 6.1.5 SFP-GIG-CWD 6.1.5 SFP-GIG-T 6.1.5...
SFP Compatibility Matrix OmniSwitch 9000E Series OmniSwitch 9000E Series The following table shows the Ethernet transceiver configurations and minimum release required for support on the OmniSwitch 9000E Series: OS9-GNI-U24E OS9-XNI-U12E SFP-GIG-SX 6.4.1 6.4.4 SFP-GIG-LX 6.4.1 6.4.4 SFP-GIG-LH40 6.4.1 6.4.4 SFP-GIG-LH70 6.4.1...
4. Supports maximum of 22 Copper SFPs on OS6855-U24X. 5. Supported on OS6855-U24X only. 6. Does not support industrial temperature ranges. * 10/100/1000 Mbps SFP transceivers are not supported on 10-Gigabit SFP+ ports. page 4-36 OmniSwitch Transceivers Guide April 2011...
6.1.3 SFP-GIG-BX-D 6.3.1 6.3.1 SFP-GIG-BX-U 6.3.1 6.3.1 1. Release 6.3.1.R02 added support for the SFP-GIG-T at 10/100/1000 Mbits on OS6850-U24X non- combo ports only. 2. SFP-GIG-T is not supported on OS6850 combo ports. OmniSwitch Transceivers Guide April 2011 page 4-37...
OmniSwitch 6250 Series SFP Compatibility Matrix OmniSwitch 6250 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6250: OS6250 SFP-GIG-SX 6.6.1 SFP-GIG-LX 6.6.1 SFP-GIG-LH40 6.6.1 SFP-GIG-LH70 6.6.1 SFP-GIG-EXTND 6.6.1 SFP-GIG-CWD...
SFP Compatibility Matrix OmniStack 6200 Series OmniStack 6200 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniStack 6200: OS6200 (All ports/All models) SFP-GIG-SX SFP-GIG-LX SFP-GIG-LH40 SFP-GIG-LH70 SFP-GIG-EXTND SFP-GIG-CWD Not supported...
The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6855: OmniSwitch 6855 Not Supported 1. OmniSwitch 6855-U24X supports 10-Gigabit SFP+ Transceivers. OmniSwitch 6850 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6850:...
The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6850E: OmniSwitch 6850E Not Supported 1. OmniSwitch 6850E only supports 10-Gigabit SFP+ Transceivers. OmniSwitch 6400 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6400:...