Error Messages - Yamaha DME64N Owner's Manual

Error Messages

Message
Error messages
Cannot Select No selectable items are available in the scene or
monitoring point list display.
Flash Rom Full The flash ROM is full.
Invalid Password An invalid password has been entered.
Low Battery The backup battery voltage is low.
MIDI Port In Use The MIDI host setting is set to the same setting as the
DME Designer application.
No Battery The battery is completely depleted.
Param Access Err Current setting cannot be displayed.
Param Set Err Current setting cannot be changed.
Saving Failed A save operation has failed.
Slots Overloaded The current being used by all cards installed in I/O slots
exceeds the rated limit.
Store Disable The scene store parameter is set to "Disable."
Status messages
The DME64N/24N clock is not in sync with the clock
CAS. In Sync Err
signal being received at the [CASCADE IN] connector.
CAS. Out Sync Err The DME64N/24N clock is not in sync with the clock
signal being received at the [CASCADE OUT] connector.
Connecting Connecting to the network.
Download Success The DME64N/24N program has been successfully
updated.
Downloading DME64N/24N program update in progress.
Duplicate IP Adr. Duplicate IP addresses.
File Operating A file operation in which the computer is manipulating
scene data (including configuration and component
data) is in progress.
Illegal MAC Adr. An illegal MAC address has been encountered.
Invalid IP Adr. The network ID address is not appropriate.
Network Busy There is too much network traffic. Communication is not
possible.
Network Error One of the following errors has occurred on the network:
• A cable has been unplugged.
• The power to a hub or router has been shut off.
• A cable is in an inappropriate state (e.g. a heavy object
has been placed on the cable, etc.). Static electricity
can also cause errors.
Network Setup Preparing network connection.
No Current Scene There is no data in the current scene.
No MAC Adr. MAC address not specified.
Panel Locked Panel operation not allowed.
Panel Unlocked Panel lock has been disengaged. Panel operation is now
possible.
Recovering A DME64N/24N program update attempt has failed, and
the previous program is currently being restored.
(Do not turn power off.)
Saving HA Info Head amplifier info save in progress.
(Do not turn power off.)
Meaning Action
Make the appropriate settings via the DME Designer
application.
Reduce the number of stored scenes.
Enter the correct password. If you have lost or forgotten
your password, contact your Yamaha service center or
representative.
Stop using the device immediately and contact your
Yamaha service center or representative.
Set the Utility MIDI page "Host" parameter to a different
port.
Stop using the device immediately and contact your
Yamaha service center or representative.
Try again.
Try again.
Stop using the device immediately and contact your
Yamaha service center or representative.
Re-install the cards so that the current limit is not
exceeded.
Set the scene store parameter to "Enable" via the Utility
display "Lock" page.
Set the device connected to the [CASCADE IN]
connector and the DME64N/24N to use the same word
clock.
Set the device connected to the [CASCADE OUT]
connector and the DME64N/24N to use the same word
clock.
None required.
None required.
None required.
Change the IP addresses so that there are no duplicates.
None required.
This could be due do a hardware malfunction. Refer this
problem to a Yamaha service center or representative.
Set an appropriate network ID address.
Check the devices connected to the network. If there are
too many devices connected, reduce the number of
devices.
Locate and eliminate the cause of the error.
None required.
Send appropriate scene data from a computer running
the DME Designer application.
This could be due do a hardware malfunction. Refer this
problem to a Yamaha service center or representative.
Press the [CANCEL] button for longer than 2 seconds to
disengage panel lock and allow panel operation.
None required.
After the program has been restored, try the update
operation again. If repeated update attempts fail, a
hardware malfunction may be the problem. Contact your
Yamaha service center or representative.
None required.
DME64N/24N Owner's Manual
Error Messages
61