Download  Print this page

Advertisement

Table of Contents
Advanced features (continued)
Connection
For details of the connection, see "LAN control UTILITY operation manual" in the CD-ROM.
When STANDBY MODE of the INSTALLATION 1 menu of the projector is set to LOW, the LAN network is disabled.
To enable the LAN network, set STANDBY MODE to STANDARD. (See page 34 .)
Configure the initial network settings first.
You can configure the initial settings using the projector menu (see pages 49 to 52) or ProjectorView Global+. For
details of ProjectorView Global+, see "LAN control UTILITY operation manual" in the CD-ROM.
Using the User Manual
The User Manual for LAN Control Utility is prepared in the Portable Document Format (PDF) in the CD-ROM.
Opening the User Manual:
1. Load the CD-ROM into the CD-ROM drive.
2. Open CD-ROM "PROJECTOR."
3. Double-click on "MANUAL_LAN.HTML" within the CD-ROM. A language selection list for the User Manual will be
displayed.
4. Move the mouse pointer to the desired language and click.
PJLink™ supported commands
The table below shows commands to control the projector using the PJLink™ protocol.
Command
Description
POWR
Power control
POWR?
Inquiry about the power state
INPT
Input switching
INPT?
Inquiry about input switching
AVMT
Mute control
AVMT?
Inquiry about the mute state
ERST?
Inquiry about the error state
LAMP?
Inquiry about the lamp state
INST?
Inquiry about the available inputs
NAME?
Inquiry about the projector name
INF1?
Inquiry about the manufacturer name
INF2?
Inquiry about the model name
INF0?
Inquiry about other information
CLSS?
Inquiry about the class information
This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by
PJLink™ Class 1, and the compliance has been verified with the PJLink™ standard specifications Version 1.0.
Remark (Parameter)
0 = Standby
1 = Power on
0 = Standby
1 = Power on
2 = Cooling down
3 = Warming up
11 = COMPUTER1
12 = COMPUTER2
21 = VIDEO
22 = S-VIDEO
31 = HDMI
32 = DVI
33 = SDI (for UD8400U and UD8400LU only)
30 = Video mute disable
31 = Video mute enable
1st byte: Fan error, 0 or 2
2nd byte: Lamp error, 0 to 2
3rd byte: Temperature error, 0 or 2
4th byte: Cover open error, 0 or 2
5th byte: Always 0
6th byte: Other error, 0 or 2
0 to 2 mean as follows:
0 = No error detected, 1 = Warning, 2 = Error
1st value (1 to 5 digits): Cumulative LAMP 1 operating time (This item
shows a lamp operating time (hour) calculated
based on that LAMP MODE is LOW.)
2nd value: 0 = Lamp off, 1 = Lamp on
3rd value (1 to 5 digits): Cumulative LAMP 2 operating time (This item
shows a lamp operating time (hour) calculated
based on that LAMP MODE is LOW.)
4th value: 0 = Lamp off, 1 = Lamp on
The following value is returned.
"11 12 21 22 31 32 33"
The projector name set on the NETWORK menu or the ProjectorView
Setup window is returned.
"MITSUBISHI" is returned.
"UD8400U", "UD8400LU", "UD8350U" or "UD8350LU" is returned.
No other information is available. No parameter is returned.
"1" is returned.
EN-59

Advertisement

Table of Contents

   Related Manuals for Mitsubishi Electric DLP UD8400U

Comments to this Manuals

Symbols: 0
Latest comments: