Wind Speed/Wind Direction Adjustment - Mitsubishi Electric PAR-F27MEA Instruction Book

(2) Wind speed and wind direction adjustment and fan operation
When you want to change the wind speed
■ While the air conditioner is operating, press the [Wind speed] button
5.
• Each time the button is pressed, the setting changes as shown be-
low.
The wind speed is displayed at 5.
• The following wind speeds can be selected:
Wind speed
4-speed model
3-speed model
2-speed model
* The wind speeds that can be selected depend on the model.
NOTES
- In cases such as the following, the liquid crystal display and unit wind
speed are different:
1. When "HEAT STAND BY" or "DEFROSTING" is displayed.
2. Immediately after heating operation (while waiting for mode selec-
tion)
3. When the room temperature is higher than the set temperature in the
heating mode.
4. Dry operation
- For 3-speed models, a central controller wind speed display and the
remote controller wind speed display may be different.
Fan operation
<When operating fan interlocked with indoor unit>
When the indoor unit is operated, the fan is automatically operated also.
Fan operation is displayed at 7.
<When operating fan only while indoor unit stopped>
■ While the air conditioner is stopped, press the [Ventilation] button 7.
The ON/OFF lamp 1 lights and fan operation is displayed at 7.
- Depending on the indoor unit and fan model, the indoor unit may operate even when only the fan was operated.
NOTES
- When "NOT AVAILABLE" is displayed when the [Ventilation] button 7 was pressed, the fan is not interlocked.
(3) How to operate the timer
There are the following three timer modes. Select one of them.
1) 1 day timer mode
In this mode, the ON and OFF timers (10-minute units) can each be set to one time within 24 hours.
This mode has the following three setting methods:
· ON timer operation
· OFF timer operation
· ON/OFF timer operation: Timer both starts and stops the air conditioner.
2) Daily timer mode
Operation of this mode is the same as that of the 1 day timer mode. However, timer operation can be set to the same time each day in accordance
with the set ON/OFF timer time. (ON/OFF timer each 1 time/daily)
3) Auto off timer mode
The OFF timer can be easily set in 30-minute units. (30 minutes to 4 hours range) When the remaining time reaches 0:00, the air conditioner stops.
When the Auto off timer mode is selected, the next time the air conditioner is started, the OFF timer operates automatically so that the timer can be
used to turn off the air conditioner if you should forget.
NOTE
When ON/OFF operation from the central controller, etc. was restricted when timer operation was set, the set ON/OFF timer is not executed. After the
restriction is removed, timer operation is performed at the ON/OFF time.
When ON/OFF operation was restricted during AUTO OFF timer operation, the remaining time at the point operation was restricted is memorized and the
air conditioner is stopped after the memorized remaining time from the time the restriction was removed.
Remote controller display
(Low) (Mid1) (Mid2) (High)
(Mid1) (Mid2) (High)
(Mid1) (High)
: Timer only starts the air conditioner.
: Timer only stops the air conditioner.
When you want to change the wind direction
■ While the air conditioner is operating, press the [Airflow] button 6.
• Each time the button is pressed, the setting changes as shown be-
low.
The wind direction is displayed at 6.
• The following wind directions can be selected:
Display
Operation Wind
mode Speed
High/Mid1
Swing
Heat/fan
Mid2/Low
High
Cool
Mid1/Mid2/Low
Swing
Not
Dry
settable
Airflow setting
when operation
–
mode was changed
* After one hour, automatically returns to the horizontal position.
* During swing operation, remote controller display and airflow vane po-
sition cannot be synchronized.
* There may not be an airflow function, depending on the model.
NOTE
- In cases such as the following, the liquid crystal display and unit airflow
may be different.
1. When "HEAT STANDBY"or "DEFROSTING" is displayed
2. Immediately after heating operation (Waiting for mode selection)
3. When the room temperature is higher than the set temperature in
the HEAT mode
<When you want to change the fan wind speed>
■ Press the [Ventilation] button 7.
Each time the button is pressed, the wind speed is changed as shown
below.
Remote controller display
Setting 1 Setting 2 Setting 3
Swing
(horizontal 0˚) (horizontal 45˚) (horizontal 60˚)
Horizontal Downward Downward
outlet 45˚ 60˚
Horizontal outlet Downward 45˚ Downward 60˚
* Horizontal after 1 hour
Cool
Dry
– –
Fan
operation
Off
(no display)
Setting 4
(horizontal 85˚)
Downward
85˚
Downward 85˚
Heating
operation
4