Table of Contents
Advertisement
Quick Links
UILT-IN GAS COOKTOPS
30" MODELS: KGCSIOOS
GSU-300
36" MODELS: KGCG260S,
KGCSl6OS,
GSUG-360, GSlJ-360
INSTALLATION
INSTRUCTIONS
INSTALLER:
FINAL CHECK LIST
PLACEMENT
OF COOKTOP
0
1. Specified
clearances
maintained
to adjacent surfaces and front of countertop.
0
2. Burner box securely anchored to cabinet top.
ELECTRICAL
0
1. Polarized
three wire 1 POVAC, 60 Hz, with proper receptacle
and overcurrent
protection
accord-
ing to specifications
given in this booklet.
GAS SUPPLY
0
1. Supply line of l/z" Black Iron pipe provided.
0
2. Pressure regulator
shipped with unit connected
to manifold.
0
3. Manual shuloff valve installed in accessible
location.
0
4. Unit tested for gas leaks.
OPERATIONAL
q
1. If used on LP gas, verify that pressure regulator and orifice hoods have been modified for use
with LP.
0
2. Burners are properly positioned.
0
3. Knobs installed on valve stems.
0
4. Each burner lights satisfactorily.
q
6. Flame adjustment
of l/z "
soft
blue cone made on each burner.
q
6. Low flame adjustment
verified.
0
7. Drip rings and grates correctly
positioned.
q
8. Grill/Griddle
Models -
Indicator light comes on when grill/griddle
element
is turned on.
0
9. Grill/Griddle
Models -
Pan/element
assembly
is property assembled
as shown in Figure 4.
0
10. Grill/Griddle
Models -
Place cover over grill or griddle.
0
11. Unless instructed
t0 leave for owner, remove all tags, labels and internal packing
materials.
FOR MAINTENANCE
- See Use 8 Care Guide.
TO LIGHT YOUR COOKTOP
DURING POWER OUTAGE - See Use & Care Guide.
THANK
YOU INSTALLER:
1. Complele
Installation
Check List.
2. Leave all literature
for customer.
3. Notify dealer that installation
is completed.
-
FOR DETAILED INSTRUCTIONS, FOLLOW METHODS DESCRIBED IN THIS FOLDER.
Advertisement
Table of Contents
Related Manuals for Maytag KGSC100S
Summary of Contents for Maytag KGSC100S
- Page 1 UILT-IN GAS COOKTOPS 30” MODELS: KGCSIOOS GSU-300 36” MODELS: KGCG260S, KGCSl6OS, GSUG-360, GSlJ-360 INSTALLATION INSTRUCTIONS INSTALLER: FINAL CHECK LIST PLACEMENT OF COOKTOP 1. Specified clearances maintained to adjacent surfaces and front of countertop. 2. Burner box securely anchored to cabinet top. ELECTRICAL 1.
-
Page 2: Installation Instructions
IMPORTANT: Read before installing to save time, work, assure proper performance, and owner’s warranty protection. INSTALLATION INSTRUCTIONS .- -4: .:.-.=z; ,,_, The installation of the cooktop must conform to local codes and utility regulationsand should be made only by a qualified technician. -
Page 3: Electrical Connection
The burner box is 3% II deep. Additional clearance is required under the back 6” of the burner box for fuel and power connections. See Figure 5. The minimal clearances between the cooktop and adjacent vertical combusti- ble surfaces is 3 II on either side and 1 II in the back. See Figures 1 A and 1 B. Use Figure 2, below, for new inStah tions or use Figure 3 below for replacement installations. -
Page 4: Unpacking The Unit
UNPACKING THE UNIT /COVER Remove packing material from unit accessories. Grill/Griddle Models - Assemble grill/griddle as shown in Figure 4. Set aside. Be sure to remove the pressure regulator and all hard- ware before disposing of carton. FLAVOR GENERATOR When raising or lowering the cooktop itself use the front INSERT two burner openings. -
Page 5: Connecting Unit To Gas
WOOD SCREW OUTER LIP WASHER CUP WASHER COUNTER COUNTER FLAT WASHER BURNER BURNER WOOD BOLT AND CLAMP ASSEMBLY SCREW AND WASHER ASSEMBLY FIgwe A Figure B BOLT AND CLAMP ASSEMBLY Figure B 1. After centering and aligning unit in cutout lift cooktop by placing a hand in each front burner opening and hold in place with the support rod. -
Page 6: Checking Gas Connections
LP GAS ADJUSTMENT Your was factory built for use with natural gas, for USE WITH LP GAS THE FOLLOWING ADJUSTMENTS cooktop MUST BE MADE. Pressure Regulator - To convert the pressure regulator for LP gas unscrew the regulator access cap, see Figure at right, turn cap over and screw it back onto the regulator. -
Page 7: Low Flame Adjustment
After each burner has been checked, close cooktop and place drip bowls in burner openings. Ignite each burner separately and examine soft blue inner core of flame. Burner flame adjustments were done in the factory inner cores should be approximately r/z inch. -
Page 8: Wiring Diagrams
SCHEMATIC WIRING DIAGRAMS ELECTRIC CmculT ‘I+ aoscowmuuoau yCg..gn10 FROM aocxws “ALI(: WARNING TO PREVENT ELECI’RICAL SWOCR: OISCONIIECT FROM ELECIRICAL SUPPLY BECORE SERHCIHG UNIT. KGCSl 00s GSU300 “Is 10 w.n I WLOL UDIlQOP C(A.RHIYG TO PREKHT ELECTRICAL SHOCK: OlSCONNECT fROY ELLCTRICAL SUPPLY BEFORE SERwClHC...