Korg Triton Le Basic Manual page 115

Hide thumbs Also See for Triton Le:
Table of Contents

Advertisement

Off: The output will not be sent to AUDIO OUT-
PUT (MAIN) L/MONO, R, or to (INDIVIDUAL) 1,
2 (After passing through the master effects, it will be
output from AUDIO OUTPUT (MAIN).) Select this
when you wish to connect the output to the master
effects in a series connection at the send levels spec-
ified by "MFX Send."
3 "MFX Send" specifies the send level from each
oscillator to the master effects.
This is valid only if "BUS Select (All OSCs)" is set to
L/R or Off.
If IFX is selected for "BUS Select (All OSCs)," the
send level to the master effects is adjusted by the
"Send 1 (MFX1)" and "Send 2 (MFX2)" parameters
(PROG 7.1: Ed-InsertFX, Setup page) after the signal
has passed through the insert effect.
Insert effect
1 Access the PROG 7.1: Ed-InsertFX, Setup page.
The Setup page displays the state of the routing and
insert effect settings. In this page you can also make
"BUS Select" settings. Use the [ ], [ ] cursor keys
to select (All OSCs), and use the [INC]/[DEC] keys
to make the setting.
2 In "Insert Effect," select the desired insert effect.
You can use the Utility "Select by Category" to
select effects from six categories.
3 In "On/Off," turn the insert effect on/off.
If this is set to Off, the result will be the same as if
00: No Effect is selected. The input sound will be
output without change.
You can use the Utility "Copy Insert Effect" to
copy effect settings from another program, etc.
4 Set the "Pan (CC#8)," "BUS Select," "S1 (Send1
(MFX1))," and "S2 (Send2 (MFX2))" parameters
that follow the insert effect.
"Pan (CC#8)": Set the pan. This is valid only if "BUS
Select" is set to L/R.
"BUS Select": Specify the output destination. Nor-
mally you will set this to L/R. If you want to output
the sound from AUDIO OUTPUT (INDIVIDUAL) 1
and/or 2, set this to 1, 2, or 1/2.
"Send1 (MFX1)," "Send2 (MFX2)": Set the send
level to the master effects. For this example, set
these to 127.
5 Move to the IFX page, and set the parameters of
the effect that you selected for the insert effect.
For details on the parameters of each effect, refer to
PG p.164–.
Master effects
The input level of the master effect is determined by
the send level 1 and 2 settings (routing step 3, or
insert effect step 4). If send levels 1 and 2 are 0, no
master effects will be applied. Send level 1 is for MFX1,
and send level 2 is for MFX2.
1 Select the PROG 7.2: Ed-MasterFX, Setup page.
2 In "Master Effect 1" and "Master Effect 2," select
the type of each master effect.
The procedure is the same as for the insert effect.
( step 1)
The input/output of the master effect is mono-on/
stereo-out. Even if you select a stereo-input type
effect, the input will be monaural.
3 In "On/Off," switch each master effect on/off.
If this is Off, the output of the master effect will be
muted.
4 Specify the routing of master effects 1 and 2.
For details on the routing settings, refer to PG p.159.
5 In "Rtn (Return 1, 2)," adjust the output level of
each master effect.
For each effect, the W value of "W/D" (Wet/Dry)
is the effect output level. This is multiplied by the
return value ("Rtn"=127 is x1.0) to determine the
actual master effect output level.
6 Move to the MFX1 or MFX2 page, and set the
parameters of the effect that you selected as the
master effect.
For details on the parameters of each effect, refer to
PG p.164–.
Master EQ
1 Use the stereo 3-band master EQ to make final
equalizing adjustments immediately before the
sound is output from the AUDIO OUTPUT L/
MONO and R jacks.
Master EQ settings can be made in "Master EQ Gain
[dB]" of the PROG 7.2: Ed-MasterFX, Setup page, or
in the Master EQ page.
For details on master EQ parameters, refer to PG
p.209.
109

Advertisement

Table of Contents
loading

Table of Contents