Korg PS60 Owner's Manual page 37

MFX1 (Mod.)
About the master effects
Send1 Modulation Return 1
MFX1(Mod)
stereo
Chain
Level
Chain On/Off
Send2
MFX2(Rev/Dly)
stereo
Reverb/Delay Return 2
L/R
stereo
The master effects do not output any direct sound
(Dry). Use the return levels "Return1" and "Return2"
to return the effect sound (Wet) to the L/R bus and mix
it into the signal of the L/R bus.
The master effects are stereo-in/stereo-out, but the
output may be monaural depending on the type of
effect that's selected.
Tip: You can use the front panel MODULATION but-
ton and knobs to directly control the Effect Type and
MFX Parameters.
Tip: You can use the Copy MFX/EQ command to copy
the master effect and EQ settings from another perfor-
mance or program.
Effect Type
This selects the effect type for master effect 1.
Choose from No Effect, St.Chorus, St.Flanger,
Vntg.Cho/Flg, and St.Phaser. If you choose No Effect,
the output from the master effect will be muted.
MFX1 Parameters
Here you can set the parameters of the effect
selected by "Effect Type." These are displayed if
you press the  button when selecting Effect Type.
St.Chorus (Stereo Chorus)
St.Flanger (Stereo Flanger)
Vntg.Cho/Flg (Vintage Chorus/Flanger)
St.Phaser (Stereo Phaser)
( "Effect types," p. 20)
Rate (Hz)
This adjusts the speed of LFO modulation.
Depth
This adjusts the depth of LFO modulation.
Feedback
This adjusts the amount of feedback.
On/Off
This turns master effect 1 on/off. When off, the output
is muted.
Return 1
This specifies the return level from master effect 1 to
the L/R bus.
Chain
On: Master effects 1 and 2 will be series-connected in
the order of master effect 1 → master effect 2.
stereo
EQ
Master Level
stereo
EQ
stereo
AUDIO OUTPUT
L/Mono, R
[No Effect...St.Phaser]
[0.01...10.0]
[0...100]
[0...100]
[Off, On]
[000...127]
[Off, On]
Performance edit Quick parameter list
Chain Level
This specifies the level from master effect 1 to master
effect 2 when "Chain On/Off" is On.
Tip: You can use the front panel MODULATION but-
ton and knobs to directly control the Effect Type and
MFX Parameters.
MFX2 (Rev/Dly)
( "About the master effects," p. 33)
Effect Type
This selects the effect type for master effect 2.
You can choose from No Effect, Hall, Plate, Room, or
Delay. If you choose No Effect, the output from the
master effect will be muted.
MFX2 Parameters
Here you can set the parameters of the effect
selected by "Effect Type." These are displayed if
you press the  button when selecting Effect Type.
Hall
Plate
Room
( "Effect types," p. 20)
Time (sec)
This specifies the reverb time.
Level
This adjusts the output level of the reverb.
Feedback
This adjusts the amount of high-frequency
attenuation.
Delay
( "Effect types," p. 20)
Time (msec)
This adjusts the delay time.
Level
This adjusts the output level of the delay sound.
Feedback
This adjusts the feedback amount of the delay
sound.
On/Off
This turns master effect 2 on/off.
Return 2
This specifies the return level from master effect 2 to
the L/R bus.
Note: The actual level is determined by multiplying
this value with the Level parameter value of Hall,
Plate, Room, or Delay.
Tip: You can use the front panel REVERB/DELAY but-
ton and knobs to directly control the Effect Type and
the MFX Parameters.
[000...127]
[No Effect...Delay]
[Hall, Plate: 0.1...10.0]
[Room: 0.1...3.0]
[0...100]
[0...100]
[0...549]
[0...100]
[0...100]
[Off, On]
[000...127]
33