Advertisement
7. Attach the two Rear Support Frames (4) to the two base rails (1 & 2) using four bolts (22), eight washers (18)
and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
8. Attach the two Pulley Support Frames (17) to the Rear Support Frames (4) and the Upright Guide Posts (10
& 12) using eight bolts (28), sixteen washers (18) and eight nuts (20) as shown. HAND TIGHTEN the bolts
a t t h i s t i m e .
9. Attach the Upper Cross Brace (11) to the two Rear Support Frames (4) using four bolts (51), eight washers
(18) and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
'10. Tighten all bolts and nuts used for assembly in previous steps.
11. Carefully insert the Left Weight Bar Knuckle (44) up through the rectangular cutout in the Pulley Support
Frame (17) and flex the Left Weight Bar Cables (24) onto the pulleys (27) so that the cables insert into the
grooves of each corresponding pulleys and allowing the Left Weight Bar Knuckle (44) to hang free. Be sure
that the cables are straight and uncrossed and cables and pulleys move smoothly.
12. Repeat the step 11 on the right side of the PROSPOT/nsssrM PC-1000.
STEP #2: SENSOR WEIGHT BAR INSTALLATION
1.
Standing in front of the PROSPOTlrressrM PC-1000. Insert one end and then the other end of the Sensor
Weight Bar (25) into the Knuckles (42 & 44). Slide the knuckles onto the Bar until they rest snugly against
the preinstalled sensor retaining collars (45 & 48) at each end of the Sensor Weight Bar (25). (There is a
rotation limi{ing pin that protrudes from the bottom of the Sensor Weight Bar (25) that must fit through a slot
in the knuckles g? A 44t as it is slid into position).
2.
Place one Plastic Locking Sleeve (39) onto each end of the Sensor Weight Bar (25) and slide them inwards
until they butt up against and secure the Weight Bar Cable Knuckle in place. Tighten Plastic Locking Sleeve
bolts securely.
3.
Place one of the Olympic Adapters (30) onto the Sensor Weight Bar (25) and slide them onto the Bar until
they touch the Plastic Locking Sleeves (39). Insert an Olympic Adapter Retaining Plug (33) onto each end
of the Sensor Weight Bar (25) so that they also go inside of the Olympic Adapters (30). Secure with two
Allen bolts (29), two washers (36) and two spring washers (56).
4.
Attach the four small plastic pipes (15) to the two Pulley Support Frames (17) using four bolts (34), eight
washers (38) and four nuts (35) as shown. Tighten the bolts securely.
5.
Attach the six Side Weight Plate Holders (14) to the two Rear Support Frames (4) using twelve bolts (53),
twenty-four washers (18) and twelve nuts (20) as shown. Tighten the bolts securely.
6.
Carefully thread the rear ends of the Cross Brace Wire Harness (8) through the middle hole on the
Electronic Box Locating Plate (13) and then attach the Locating Plate (13) to the Lower Cross Brace (3)
using two bolts (22), four washers (18) and two nuts (20). Tighten the bolts securely.
7.
Attach the Electronic Box Protecting Cover (5) to the Locating Plate (13) using two cross screws (52) and
lwo washers (57) as shown. Tighten the screws securely.
Note: In this manual when referring to Left and Right side of unit, the left and right perspective
are from the outside, facing the front of the unit.
--2--
Advertisement
