Basic Operation; Listening To The Tuner - Marantz SR4200 User Manual

Av surround receiver
Hide thumbs Also See for SR4200:
Table of Contents

Advertisement

BASIC OPERATION

LISTENING TO THE TUNER

MANUAL TUNING
To select the tuner as the source, press the TUNER button t on
1.
the front panel or press the TUNER button c on the remote.
Press the TUNER button t on the front panel or press the
2.
TUNER button c on the remote to select the desired frequency
band if required.
Press the F/P button !4 on the front panel to display the frequency.
3.
button !3 on the front panel or
4.
Press the TUNING/PRESET
or
press the 1 or ¡ button ⁄2 on the remote.
If FM is selected, press the MODE button !5 on the front panel or
5.
press the MODE button ⁄2 on the remote control to select the
desired audio mode.
(FM) MODE BUTTON OPERATION
When “M” indicator is on in the display, FM stations that broadcast in
stereo will be received in stereo and the “STEREO” indicator lights.
When “M” indicator is off, all the FM stations will be received in mono
regardless of whether or not they are broadcasting in stereo.
AUTO TUNING (USING THE SR4200)
Press the F/P button !4 on the front panel to display the frequency.
1.
button !3 on the front panel
2.
Press the TUNING/PRESET
or
for more than 1 second to start the Auto tuning function.
AUTO TUNING (USING THE REMOTE CONTROL UNIT)
Press 1 or ¡ button ⁄2 for more than 1 second to start the Auto
tuning function.
PRESET TUNING
With this unit you can preset up to 50 FM/AM (MW/LW) stations in any
order. For each station, you can memorize the frequency and
reception mode if desired.
1-a. Manual Presetting (Using the SR4200)
1.
Refer to the “MANUAL TUNING” or “AUTO TUNING” section
above to tune in a desired station.
Press the MEMORY button !2 . “MEMO” indicator starts blinking
2.
on the display.
While “MEMO” is still blinking (approx. 5 seconds), select the
button !3
preset number by pressing the TUNING/PRESET
or
then press the MEMORY button !2 again.
3.
When a number has been properly input, “MEMO” indicator stops
blinking and goes out.
The station is now stored in the specified preset memory location.
1-b. Manual Presetting (Using the remote control unit)
1.
Tune in a desired station.
Press the MEMO button ⁄6 .
2.
Enter the desired preset number with ten keypad ..
3.
* When entering a single digit number (2, for example), either input
“02” or just input “2” and wait for a few seconds.
* If a number other than 1-50 is entered by mistake, that number
flashes in the display to indicate that it is invalid and the display
returns to the original frequency display.
2. Auto Presetting
This function automatically scans the AM (MW/LW) and FM band and
enters all stations with sufficient signal strength into the memory.
Select the FM band with the TUNER button t.
1.
2.
Tune in the lowest receivable frequency.
Press and hold down the MEMORY button !2 and TUNING/
3.
button !3 simultaneously, auto presetting will starts.
PRESET
4.
Each time the tuner finds a station, the scanning will pause and
memory.
5.
Operation stops automatically when all 50 preset memory
positions are filled or when auto scanning attains the highest end
of all bands.
To stop the auto preset function at anytime, press the CLEAR
button !1 .
3. Recalling a Preset Station
Press the F/P button !4 to change the display to preset.
1.
2.
Select the desired preset station by pressing TUNING/PRESET
button !3 on the front panel or press CHANNEL button ⁄2
or
on the remote.
Note:
To directly access the preset stations using the numeric keypad,
select the desired preset station by entering one or two digits using
the numeric keypad ..
To return to the Manual Tuning mode, press the F/P button !4 .
4. Preset Scan Tuning (Using the remote control unit)
Press the P.SCAN button ⁄0 on the remote control. (The preset
1.
station with the smallest preset number is recalled first. If no
stations have been preset, CH “00” blinks in the display and the
unit returns to the previous mode.)
Preset stations are recalled in sequence (CH-1 → CH-2, etc.) for 5
2.
seconds each. Preset numbers that do not contain stations are
skipped.
3.
You can fast forward the preset stations by pressing the
CHANNEL ¢ button ⁄2 continuously.
When the desired preset station is received, cancel the preset
scan operation by pressing the CHANNEL 4 button ⁄2 or the
CLEAR button !1 .
5. Clearing Preset Stations
You can remove preset stations from memory using the following
procedure.
1.
Recall the preset number to be cleared with the method described
in “Recalling” a preset station .
Press the MEMORY button !2 on the front panel or MEMO button
2.
⁄6 on the remote unit, “MEMO” blinks in the display for 5 seconds.
While “MEMO” is still blinking, press the CLEAR button !1 on the
front panel or CLEAR button ⁄7 on the remote unit.
“CLEAR” appears on the display to indicate that the specified
preset number has been cleared.
Page 13

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents