Pausing Or Restarting; Changing Cycles, Options And Modifiers; Status Lights - Whirlpool Duet HT GHW9250ML1 Use & Care Manual

Front-loading automatic washer
Hide thumbs Also See for Duet HT GHW9250ML1:
Table of Contents

Advertisement

Available languages

Available languages

Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
Do not fill beyond the "MAX" level. Overfilling could cause
severe garment damage.
Fabric Softener
compartment
(Number 6 in Dispenser Illustration)
Add 1/4cup (60 mL) liquid fabric softener to this compartment.
Fabric softener will be automatically
dispensed
in the final rinse.
Do not fill beyond the "MAX" level.
1.
2.
,
¢
To pause the washer at any time, select PAUSE/CANCEL
To continue the cycle, select HOLD TO START (for
approximately
1 second).
Not all Options and Modifiers are available with all cycles. Cycles,
Options and Modifiers can be changed anytime before HOLD TO
START is selected.
Options and Modifiers can be changed anytime after HOLD TO
START is selected and before the start of the selected Option or
Modifier.
To cancel a cycle and select a new cycle
1. Select PAUSE/CANCEL twice.
2. Select desired cycle.
3. Select the desired OPTIONS.
4. Select HOLD TO START (for approximately
I second) to
restart the washer at the beginning of the new cycle.
To cancel a cycle
1. Select PAUSE/CANCEL twice.
2. The washer powers down, the door unlocks, and clothes can
be removed.
NOTE: If the water level or the temperature
is too high, the
washer will drain automatically
before the door unlocks.
To change Options or Modifiers after the cycle has started
1. Select PAUSE/CANCEL
2. Select the desired OPTIONS or MODIFIERS.
3. Select HOLD TO START (for approximately
1 second) to
continue the cycle.
To drain the washer manually
1. Select PAUSE/CANCEL
2. Select DRAIN/SPIN.
3. Select HOLD TO START (for approximately
1 second) to
begin the drain.
4. When the spin is complete, the door unlocks. Items can be
removed from the washer.
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
Status
Q Delay Wash
@ Add a Garment
@ Soak/Prewash
• Wash
@ Rinse
• Spin
O Cycle Complete
@ Control Locked
Adding items
You can add items to the washer after the cycle has started for
Sanitary, Whitest Whites, Heavy Duty, Normal and Quick Wash, if
the ADD A GARMENT status light is glowing.
To add items
1. Select PAUSE/CANCEL. The washer door unlocks, and items
can be added.
2. To continue the cycle, close the door and select HOLD TO
START (for approximately
1 second).
Cycle Complete
The cycle complete light stays on for 5 minutes after the cycle is
complete, and then the washer shuts off.
Locking
controls
The Control Lock prevents unintended use of the washer. You
can also use the control lock feature to prevent unintended cycle
or option changes during a cycle. When CONTROL LOCKED is
lit, all buttons are disabled except for PAUSE/CANCEL and
START. You can lock the controls while the washer is operating.
To lock the controls
Select and hold END OF CYCLE SIGNAL for 3 seconds.
O Louder
Softer
o off
End
Ot Cycle
Signal
LocMUnlock Cor,tro3
The CONTROL LOCKED status light glows.
To unlock the controls
Select and hold END OF CYCLE SIGNAL for 3 seconds until the
CONTROL LOCKED status light turns off.
Estimated
time remaining
The cycle time varies automatically
based on your water
pressure, water temperature,
detergent and clothes load. The
cycle time will be extended if oversudsing
occurs or the load is
unbalanced.
Page 12

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents