Table of Contents
Advertisement
Available languages
Available languages
Cycle time too short
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
•
Is the automatic cycle ending early?
The load may not be contacting the sensor strips. Level the
dryer.
Change the dryness level setting on Automatic
Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
Lint on load
•
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Stains on load or drum
•
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets with
steam cycles.
Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
Loads are wrinkled
Was the load removed from dryer at the end of the cycle?
Select Enhanced Touch Up Cycle to tumble the load with
water and heat. This cycle is best for smoothing out wrinkles
and reducing odors from loads consisting of wrinkle-free
cotton, cotton polyester blends, common knits and synthetic
garments.
NOTE: Refer to garment care label instructions. Dry clean only
garments are not recommended.
Loads are still wrinkled following
Steam Cycle?
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer's water
inlet valve. Check that the water supply is turned on.
Was the dryer overloaded?
Dry smaller loads that can tumble freely. Smaller loads of 1-4
garments yield best results with Quick Refresh Cycle. Results
may also vary depending on fabric type. This cycle is best for
reducing wrinkles and odors from loads consisting of wrinkle-
free cotton, cotton polyester blends, common knits and
synthetics.
Odors
•
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
Is water connected
to the dryer?
Check that water inlet hose is connected to both the faucet
and dryer's water inlet valve. Check that the water supply is
turned on.
To remove odors left in garments after wearing, select Quick
Refresh for small loads of 1-4 garments. This cycle is best for
reducing wrinkles and odors from loads consisting of wrinkle-
free cotton, cotton polyester blends, common knits and
synthetics.
ASSISTANCE ORSERVICE
Before calling for assistance or service, please check
"Troubleshooting."
It may save you the cost of a service call. If
you still need help, follow the instructions
below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement
parts
If you need to order replacement parts, we recommend that you
use only FSP° factory specified parts. These parts will fit right
and work right because they are made with the same precision
used to build every new WHIRLPOOL ® appliance.
To locate
FSP replacement
parts in your area:
Call f-800-807-6777,
or your nearest designated service center.
Our consultants
provide assistance
with:
•
Features and specifications
on our full line of appliances.
•
Use and maintenance procedures.
•
Accessory and repair parts sales.
Referrals to local dealers, repair parts distributors,
and
service companies. Whirlpool Canada LP designated
service
technicians are trained to fulfill the product warranty and
provide after-warranty
service anywhere in Canada.
For further
assistance
If you need further assistance, you can write to Whirlpool Canada
LP with any questions or concerns at:
Customer Interaction Centre
Whirlpool Canada LP
1901 Minnesota Court
Mississauga,
Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
21
Advertisement
Table of Contents
