Table of Contents
Advertisement
Using th( Remot
Control
VCR1
Puts the remote in VCR1 mode and, if Autotuning
is enabled, will turn on the TV and tune to the correct
input channel
VCR2
Puts the remote in VCR2 mode and, if Autotuning
is enabled, wii[ turn on the TV and tune to the correct
input channel
VOL - or VOL +
Decreases or increases the IV's volume,
ZOOM+ or ZOOM-
When watching IV, changesthe current format of the screen (4x3, Zoom 1419,Zoom 1619,
Zoom 16/9 _Iv, Cinerama, regular mode 1619).
Using the INPUT Button
Usethe INPUTbutton to scroll through the available input channels and view components you have connected to
the IV.
I.
PressIV to place the remote in IV mode. Make sure the component you want to view is turned ON.
2.
PressINPUTto tune to an available input channel.
3.
To return to the channel you were previously watching on IV, pressCH+ or CH- button,
VCR1
ON= OFF
TV
•
_VD
VCff2
AUX SAT=CABLE
Indicator
_EVE_SEPLaY
You'lluse these buttons when you program
theremote.
#nportun b Theremote,may not he compatible with eft
modelsof ull brandsof components, it ol5o muy not
operute aft functions of the remote thut came with
your componenL
Tip
Tostop the uutomatic code 3eurchwithout programming
any components, press and hold CLEAR untit the indicator
on the remote turns off.
Programming
the Remote to Operate
Other
Components
The universal remote can be programmed
to operate most brands of remote controllable
components. The remote is already programmed to operate most RCA, GE, and Proscan
components.
Also, the AUX button
can be programmed to operate most brands of an additional
remote-
controllable
component,
Note: TheIV button can't beprogrummed on this remote,.
Find Out If You Need to Program the Remote
To determine whether the universal remote needs to be programmed
for your component,
turn
the component
ON. For example, to program the remote for a VCR, turn on the VCR. Point the
remote at the VCR, and press the VCR1 button,
Then press ON,OFF or CH + (channel up] or CH -
(channel down) to see if the VCR responds to the remote commands, If the component
does not
respond, the remote needs to be programmed,
Programming
the Remote
There are two ways to program the remote controh
automatic code search
direct entry
Using Automatic
Code Search
The following
instructions
can be used to program the remote to operate each of your
components. If you want to stop the automatic
code search without
programming
any of your
components, press CLEAR until the indicator
on the remote turns off.
I.
Turn on the component
you want to operate (VCR, DVD player, eta,)
2.
Press and hold the component
button
you want to program (VCR1, DVD, eta,), While holding
the component
button,
press and hold ON,OFF until the indicator
on the remote turns on,
then release both buttons,
3.
Point the remote at the component.
Press and release PLAY, then wait 5 seconds or until the
indicator
on the remote stops flashing,
At this point the remote is searching for the correct code to program. If, after 5 seconds, the
component
you want to operate does not turn off, press PLAY again to tell the remote to
search the next set of codes.
Continue pressing PLAY until the component
turns oft or you have searched through all of
the codes. There are 20 total sets of codes, If the component
does not turn off after pressing
PLAY 20 times, then the remote can't be programmed
to operate that component,
If the component
you want to control does turn off:
I.
Press and release REVERSE,then wait 2 seconds, Repeat this step until the device turns back
ON.
2.
To finish, press and hold STOP until the indicator
on the remote turns off,
14
Graphics confined
within this publication ore for representation only.
Cha_te_" 2
Advertisement
Table of Contents
