Electrolux ICON appliances Design Manual page 159

Electric Cooktop Installation Over 30" Electric Single Wall Oven
For all approved electric cooktop models, cut minimum
4" x 4" opening in right cabinet side panel and/or filler
panel, to route armoured cable to junction box
Side filler panels necessary to isolate oven from
adjoining cabinets. Panel height may need to
be modified to accommodate the depth of approved
electric cooktop models
Electric Single Wall Oven Cutout Electric Single Wall Oven Cutout
For models: E30EW75GPS For models: E30EW75GPS
& E30EW75GSS & E30EW75GSS
Approx. 3"
240/208V
Junction box
for wall oven
24" min.
cutout depth
4-1/2" maximum height allowed
from oven base to floor if cooktop
is installed directly over wall oven.
(5" maximum height allowed
with no cooktop.)
Installation Specifications
30" Electric Single Wall Oven
Under-Counter Installation Specifications
• Product Weights –
(E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
• Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208
Volt, 60 Hertz AC only electrical supply with ground
required on separate circuit fused on both sides of line.
• Connected Load (kW Rating) @ 240 / 208 Volts =
4.0 / 3.0 kW
• Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
• Always consult local and national electric and gas codes.
• Minimum 23-1/4" clearance for oven door depth
when open.
• Minimum 24" deep cutout dimension is critical for
proper installation, to ensure that oven's faceplate will fit
flush against cabinet front.
• Full oven base of solid plywood or similar material required,
capable of supporting 200 Lbs. Install over two runners
and flush with toe plate.
• Base must be level and cabinet front must be square
with finish-cut bottom edge.
• Side filler panels necessary to isolate oven from adjoining
cabinets.
• Allow 5" maximum height from oven base to floor, if NO
cooktop is installed directly over wall oven.
Cooktop
Approx. 3"
cutout**
24"min.*
28 / " min.
1
2
29" max.
Install / " full plywood base on 2 runners, flush
3
4
with toe plate, capable of supporting 200 lbs.
Unit will overlap cutout (minimum) edges by 1"
To route armored cable to junction box through left cabinet side panel
and/or filler panel, cut minimum 4" x 4" opening in wood base and runner
Electric Cooktop Installation Over
30" Electric Single Wall Oven Specifications
Electrolux ICON
and E30EW75GSS are approved to be used beneath
Electrolux ICON
E30IC80ISS, E36EC70FSS and E30EC70FSS (electric
cooktop models NOT approved for use in this installation
are E36EC75HSS, E30EC65ESS and E36EC65ESS).
For detailed Electric Cooktop installation, refer to
model-specific Planning Information page and installation
guide on web.
• Side filler panels necessary to isolate oven from adjoining
cabinets. Panel height may need to be modified to accom-
modate the depth of approved electric cooktop models.
• To route armored cable to junction box, cut minimum
4" x 4" opening in right cabinet side panel.
• Allow 4-1/2" maximum height from oven base to floor,
if cooktop is installed directly over wall oven.
240 /208V
Junction box
for electric
cooktop
Oven cutout
36"
min.
28 / " min.
1
2
28 / " max.
7
8
®
Single Wall Oven models E30EW75GPS
®
electric cooktop models E36IC80ISS,
e l e c t ro l u x i c o n . c o m
planning
information
For models:
Cooktop
E30EC70FSS
E30IC80ISS
E36EC70FSS
E36IC80ISS
Single Wall Oven
E30EW75GPS
E30EW75GSS
Note: For planning
purposes only. Refer
to Product Installation
Guide on the web at
electroluxicon.com for
detailed instructions.
Specifications subject
to change.
159