Operating Your Air Conditioner; Starting Your Air Conditioner - Whirlpool YACQ082XK1 Use And Care Manual

Table of Contents

Advertisement

Operating
Your Air Conditioner
Operating your air conditioner properly helps you to obtain the best possible results.
This section explains proper air conditioner operation.
iMPORTANT:
• If you turn the air conditioner off, wait at least 3 minutes before turning it back on. This prevents the air conditioner from
blowing a fuse or tripping a circuit breaker.
• Do not try to operate your air conditioner in the cooling mode when outside temperature is below 65°F (18°C). The
inside evaporator coil wiii freeze up and the air conditioner will not operate properly.
Starting
your
air conditioner
Press Power ON/OFF to turn on air
conditioner. When air conditioner
is turned on
for the first time after it is plugged in, it will
display the default settings: COOL mode, TURBO fan
speed, 72°E When it is turned on all other times, it will
display the previous settings.
TEMPERATURE
SELECTION
Press A to raise the temperature.
Each time you press or hold A,
the temperature will go up 1° until
it reaches 86°E
Press v
to lower the temperature.
Each time you press or hold 'v, the temperature will
go down 1° until it reaches 64°R
MODE SELECTION
Press MODE until you see the indicator light
,, AUTO
e COOL
come on for the setting you want. Choose
FAN
AUTO, COOL, FAN or POWER SAVER.
,, _o_R
AUTO - Cools room while it automatically
/_X
controls fan speed. You cannot change fan
speed, but you can adjust temperature
by
pressing A or v.
COOL - Cools room. You can select fan speed by
pressing FAN SPEED. You can then adjust
temperature by pressing A or .,v.
FAN ONLY - Fan runs on TURBO speed only. Only
the fan runs. Display shows "FO" (fan only).
POWER SAVER - Fan runs only when cooling is
needed. Fan stops running when the room
temperature matches the temperature you set.
Press FAN SPEED until you see the indicator light
for the setting you want. Choose TURBO, HIGH
or LOW.
Select the temperature by pressing A or v.
FAN SPEED SELECTION
,, TURBO
NOTE: FAN SPEED button will operate only
,.._o,
when COOL or POWER SAVER mode has
,, Low
been selected.
@
Press FAN SPEED until you see the indicator
light for the setting you want. Choose TURBO,
HIGH or LOW.
TIMER DELAY
The TIMER can be set for a 1 to 24 hour delay
until the air conditioner turns on or off.
Press A or v
to adjust the delay time.
To set the TIMER delay to turn the air
conditioner off, air conditioner must be in the
ON mode.
Press TIMER ON/OFF. (Indicator light will flash.)
Press A or v to change delay time (1 to 24 hours).
Press TIMER ON/OFF or wait 10 seconds. (Indicator
light will remain on.)
To set the TIMER delay to turn the air conditioner on, air
conditioner must be in the OFF mode.
If you want to change the previous settings:
Turn air conditioner on.
Adjust MODE to AUTO, COOL, FAN, or POWER
SAVER.
Adjust FAN SPEED to TURBO, HIGH or LOW.
Adjust TEMPERATURE
between 64°F and 86°E
Turn air conditioner off.
Press TIMER ON/OFE (Indicator light will flash.)
Press A Dry
to change delay time (1 to 24 hours).
Press TIMER ON/OFF or wait 10 seconds.
if you want to keep the previous
settings:
Turn air conditioner off.
Press TIMER ON/OFF. (Indicator light will flash.)
Press A or v
to change delay time (1 to 24 hours).
Press TIMER ON/OFF or wait 10 seconds.
To clear TIMER delay program, press and hold TIMER
ON/OFF for 3 seconds. Indicator light will shut off. Air
conditioner can be either on or off.
To see the remaining time (in hours), press TIMER
ON/OFF once after it has been programmed. While the
display is showing the remaining time, you can
press A or .,v to increase or decrease the time.

Advertisement

Table of Contents
loading

Subscribe to Our Youtube Channel

Table of Contents