Whirlpool GU2300XTVS2 User Instructions page 4

Depending onyour w ater h ardness, filltheMain Wash s ection
ofthedispenser asshown. Fill t hePre-Wash section t othe
level shown, ifneeded.
NOTE: Fillamounts shown
areforstandard powdered
detergent. Follow i nstructions
onthepackage when using
other d ishwasher detergent.
Add Rinse Aid
HardWater
Soft Water
HardWater
Soft W ater
MainWash Pre-Wash
Your dishwasher is designed to use rinse aid for good drying
performance. Without rinse aid your dishes and dishwasher
interior will have excessive moisture. The heat dry option will
not perform as well without rinse aid.
Rinse aid keeps water from forming droplets that can
dry as spots or streaks. They also improve drying by
allowing water to drain off of the dishes after the final
rinse.
Rinse aid helps to reduce excess moisture on the dish
racks and interior of your dishwasher.
Full
Add
Check the rinse aid indicator. Add rinse aid when indicator
drops to "Add" level.
To add rinse aid, turn the dispenser cap
to "Refill" and lift off. Pour rinse aid into
the opening until the indicator level is at
"Full." Replace the dispenser cap and
turn to "Lock." Make sure cap is fully
locked.
NOTE: For most water conditions, the
factory setting of 2 will give good
results. If you have hard water or notice
rings or spots, try a higher setting. Turn
the arrow adjuster inside the dispenser
by either using your fingers or inserting
a flat-blade screwdriver into the center
of the arrow and turning.
Lock
Refill/_
¼ turn to lock
STEP 3
Select a Cycle (cycles vary by model)
See "Cycle and Option Descriptions" charts in the following
section.
Heavier cycles and options affect cycle length. Some cycles and
options will take up to 31/2hours to complete.
CYCLES
O O O O O 0
000000
ADAPTIVE POTS & NORMAL CHINA GLASS RINSE
WASH PANS XPRESS ONLY
Select Options (options vary by model)
See "Cycle and Option Descriptions" charts in the following
section.
You can customize your cycles by pressing the options desired.
OPTIONS
2 4 6
@ @ @ ® 0 @ OO® @
0 0000 @ @
SOAK& PowerScour HI-TEMP SANI- HEATED DELAY 4HOUR
SCOUR WASH RINSE DRY DELAY
STEP 4
Start or Resume a Cycle
• Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water. For best dishwashing results, water
should be 120°F (49°C) as it enters the dishwasher.
• Push door firmly closed. The door latches o
automatically. Select the wash cycle and options
desired OR press START/RESUME to repeat the same
k.TJ
cycle and options as in the previous wash cycle.
START /
• You can add an item anytime before the main wash RESUME
starts. Open the door slowly and add the item. Close
the door firmly within 3 seconds. Press START/RESUME.
, ;_ ,_',s,,_ _ ;,;.... .......... ,, ..........
CYCLES
@ 0 @ @ @ @
000000
ADAPTIVE POTS& NORMAL CHINA GLASS RINSE
WASH PANS XPRESS ONLY
This information covers several different models. Your dishwasher may not have all the cycles and options described.
You can customize your cycle by selecting an option.
See option selections. If you change your mind, press the option again to turn off the option, or select a different option. You can change
an option anytime before the selected option begins.
*Maximum wash times depend on water temperature, heavy soil condition, dish load size and options selected.
CYCLES DISH LOAD TYPES DESCRIPTIONS WASH TIME (HH:MM)
Cycle Cycle + Options *Maximum
Minimum Minimum
0 use for all day,to,day soil This Cycle Compensates for the size of
types when washing fu!l to the dish !oad by adding time and heat:
partial dish loads
: During the wash; the wash action will
AD_VE repeatedly pause for severa! seconds,