Table of Contents
Advertisement
SETTINGS
You can set the screen aspect
ratio of the connected
T_, and adjust the video output.
If you switch your TV (i,e. because you have bought
a
new one) and the screen aspect
ratio of the connected
TV changes, you will have to change the "TV Aspect
Ratio" setting.
IW Item
ide 16:9: Sebct this wherl connecthTg to a TV with a
16:9 screen aspect ratio.
orma( 4:3: Sebct ttlis when connecting to a TV with a
4:3 screen aspect ratio.
<When
selecting
Normal
4:3>
item
Letter Box: If you connect to a TV with a screen aspect
ratio of 4:3 and p(ayback a DVD with 16:9 video, the
video wi(( be played back with b(ack bands at the top
and bottom while maintaining the 16:9 ratio.
Par] Scar]: If you connect to a TV with a screen aspect
ratio of 4:3 and p(ayback a DVD with 16:9 video, the
video wi(( be played back with the left and right sides of
the image cut off to display in 4:3 screen aspect ratio.
(Thb function works if the disc is labe(bd for 4:3PS.)
This sets the resolution
of the component
video
output.
Some TVs are not fully compatible
with the Blu-ray
disc player, which may cause the image distortion.
In this case, press VIDEO
OUTPUT
RESET on the
remote control
for five seconds.
"Component
Video
Out" will be reset to "480i" (factory preset value).
_1
Item
1
080i, 720p, 480p, 480i
/
This sets the resolution
of the HDMI video output.
Some TVs are not fully compatible
with the Blu-ray
disc player, which may cause the image distortion.
In this case, press VIDEO
OUTPUT
RESET on the
remote control
for five seconds.
"HDMI Video Out" will
be reset to "Auto"
(factory preset value).
'-A Item
uto, 1080p, 1080i, 720p, 480p
NOTE
" When the BD player is connected to a 1080p 24Hz
compatible TV and the "HDMI Video Out" is set to
"Auto", 1080p 24Hz will automatically be displayed when
compatible discs are played back.
At 1080p 24Hz/1080p 60Hz, there is no output from the
COMPONENT VIDEO OUT jacks and VIDE() output jack.
}
Dual video output
is possible
simultaneously
from the
COMPONENT
VIDEO OUT jacks and the HDMI OUT
terminal
with the following
settings.
Select the video
output
which you want to have priority according
to
the following
chart.
NOTE
1080p aridAQUOSLINKare only available in HDMI.
Video
Out
Dual
HDMI
Select
Output
Video
Out
No
Auto
No
1080p
HDMI
Yes
108@
Yes
720p
Yes
480p
Dual
Component
Output
Video
Out
Yes
108@
Component
Yes
720p
Yes
480p
Yes
4801
Component
Out Resolution
in Dual
Mode
"1
No
1080(
720p
480p
HDMI
Out
Resolution
in
Dual
Mode
1080(
720p
480p
48@
"1 Depends on source. 1080p is not available.
-H Item
DMI, Component
- When the priority video output is selected, video is output
from the other video terminal with the resolution of the
selected video output.
- There is no output from the COMPONENT VIDEO OUT
jacks and VIDEO output jack when video is output at
1080p resolution and the priority video output is selected
to "HDMr'.
- If the video equipment connected to each of the terminals
is not compatible with the resolution of the priority video
output, abnormalities in images on the screen may appear.
NOTE
When you select the priority video output, this function car]
also be performed by pressing the HDMI button of the
remote control.
!!!!!!2!ii! ........................
I
HDMI
Press and hold HDMI button for 5 seconds to switch
between "HDMI OUT" and "COMPONENT VIDE()OUT".
}
- While you are holding the button, the current output setting
will be shown with the display blinking, and then the
switched output setting will be displayed or] the front panel
display.
" "H - o P" (HDMI OUT) or ,,r_p _ c] i9'' (COMPONENT
VIDEO OUT) is displayed alternately on the front panel
display.
(ConthTued orl the next page)
Q- 49
m
Advertisement
Table of Contents
