Download Print this page

KitchenAid KXW4330YSS0 Installation Instructions And Use & Care Manual page 4

30" (76.2 cm) and 36" (91.4 cm) wall-mount canopy range hood
Hide thumbs

Advertisement

Table of Contents
For non-vented (recirculating) installations, you will also
need:
Recirculation
Kit Part Number W10344022 for non-vented
(recirculating)
installations only. See "Assistance
or Service"
section to order.
6" (15.2 cm) dia. round metal vent duct - length required is
determined by ceiling height.
Parts supplied
Remove parts from packages. Check that all parts are included.
Hood canopy assembly with ventilator and light bulbs
installed
Vent transition with back draft dampers installed
Metal grease filter(s) - depending
on model and size
Vent cover support bracket
Mounting template
2-piece vent cover
4-4xascrews
6- 5 x 45 mm mounting screws
2 - D6.4 x 18 mm washers
2 - 8 x 40 mm wall anchors
4- 10 x 50 mm wall anchors
II,OCIIIIIOI] ">" ="
...............
"
°
l:,,,,_:_q
I, 111 1 II) I 15 ,_,
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located behind the left filter on the rear wall of the vent
hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented
(recirculating) installation see "For non-
vented (recirculating) installation only" in the "Connect Vent
System" section. Recirculation
Kit Part Number W10344022
is
available from your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities
and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
10¾" (27.
3%" (8.6 cm)
cm)
13%o"
*28%o" (71.9 cm) rain.
42%" (108.3 cm) max.
2f'cm
**24%" (62.5 cm) rain.
(98.4 cm) max.
30" (7(
36" (91.4 cm).
*For non-vented
(recirculating)
installation
**For vented
installations
*For non-vented
(recirculating) installations
**For vented installations
Cabinet Dimensions
91/2" (24.1
10" (25.4 cm) rain.
13" (33.0 cm) max.
-,_\_=_====_..,
2" (5.1 cm) rain.
).9 cm) rain.*
10" (25.4 cm) rain.
13" (33.0 cm)
Side
cabinet
Vent and power
supply cable
_
entry location
............
I . ..........
)
/
i
.../
(
17" (43.2 cm)*
//
//+
I
ii.
Side
cabinet
_
30" (76.2
--
36" (91.4 cm)
"X"
i
bottom
of
canopy
to cooking
I
surface
(Centerline
Cookinq surface
*For non-vented
(recirculating) installations
IM PO RTANT:
Minimum distance "X": 24" (61.0 cm) from electric cooking
surface.
Minimum distance "X": 27" (68.6 cm) from gas cooking
surfaces.
Suggested maximum distance "X": 36" (91.4 cm)

Hide quick links:

Advertisement

Table of Contents
loading

  Related Manuals for KitchenAid KXW4330YSS0

This manual is also suitable for:

Kxw4336yss0Kxw4336yss1Kxw4330yss1