Dryer Use - KitchenAid KEHS02RWH0 Use & Care Manual

Front-loading electric dryer
Table of Contents

Advertisement

Available languages

Available languages

4. Move hinge to the other side and reattach with the 4 screws
removed in Step 2.
5. Move handle bracket to the other side and reattach with the
2 screws removed in Step 3.
6. Set the inner door assembly aside.
Reinstalling
the door
1. Check for fingerprints
on the glass. Clean if necessary.
2. Place the inner door assembly into the outer door assembly.
Align the hinge in the opening on the side. To fit correctly, the
inside door assembly edge is completely inside the outside
door assembly edge.
3. Reassemble the inner and outer door assemblies with the
6 screws.
4.
5.
Replace the 2 handle screws for the door handle of the door
assembly.
Use a small flat-blade screwdriver to remove plug strip in the
door opening. Slide the head of the screwdriver under the top
portion of the plug strip, being certain not to scratch the dryer
surface. Lift up. Repeat in the middle and at the bottom.
Remove the plug stripe in the door opening and insert in the
opposite side.
6=
Insert a screw in the second opening from the top of the
hinge opening and partially tighten. Hang the door by placing
the top hinge keyhole over the second screw head and
tighten the screw. By putting this screw in first, the door will
hang in place while you insert and tighten the remaining
4 screws.
\
A. Dryer door
B. Dryer
C. Insert this screw first
7. Close the door and check that it latches securely.
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check the dryer's final location. Be sure the vent is not
crushed or kinked.
5. Check that the dryer is level. See "Level Dryer."
6. In the U.S.A.
For power supply cord installation, plug into a grounded
outlet. For direct wire installation, turn on power.
In Canada
Emectdcal Shock Hazard
Pmug into a grounded
4 prong outlet.
Failure to do so can result in death or electrical
shock.
Plug into a 4 prong grounded outlet. Turn on power.
7. Remove the blue protective film on the console and any tape
remaining on the dryer.
8. Read "Dryer Use."
g. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
10. Set the dryer on a full heat cycle (not an air cycle) for
20 minutes and start the dryer.
If the dryer will not start, check the following:
11.
Controls are set in a running or "On" position.
Start button has been pushed firmly.
Dryer is plugged into a grounded outlet and/or electrical
supply is on.
Household fuse is intact and tight, or circuit breaker has
not tripped.
Dryer door is closed.
When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you feel heat, cancel cycle and
close the door.
If you do not feel heat, turn off the dryer and check the
following:
There may be 2 household fuses or circuit breakers for
the dryer. Check to make sure both fuses are intact and
tight, or that both circuit breakers have not tripped. If
there is still no heat, contact a qualified technician.
NOTE: You may notice a burning odor when the dryer is first
heated. This odor is common when the heating element is first
used. The odor will go away.
18

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ykehso2rwhoKehs02rmt0Ykehso2rmt0

Table of Contents