Table of Contents
Advertisement
Sealed Surface Burner
Models-
Setting
Surface Controls
The surface
control
knob shown
below
may not
look identical
to the surface
control
knobs
on your
range;
it is only
representational.
Do not
place
plastic
items such as salt and pepper shakers,
spoon
holders
or plastic
wrappings
on top of the range when it is in use.
These items
could
melt
or ignite.
Potholders,
towels
or wood
spoons
could catch fire if placed too close to a
flame.
In the
event
of
an electrical
power
outage,
the surface
burners
can be lit
manually.
To light
a surface
burner,
hold
a lit match
to the
burner
head,
then
slowly
turn
the Surface
Control
knob to LITE. After
burner
lights
push
in and turn knob to desired
setting.
Use
caution
when
lighting
surface
burners
manually.
Your range may be equipped
with
any combination
of the following
burners:
Simmer
Burner,
this burner
is best used for simmering
delicate
sauces, etc.
Standard
Burner,
can be used for most
all surface
cooking
needs.
Large Burner,
the larger
burner
is best used when
bringing
large quantities
of
liquid
to temperature
and when
preparing
larger
quantities
of food.
Regardless
of size, always
select a utensil
that
is suitable
for the amount
and
type of food
being
prepared.
Select a burner
and flame
size appropriate
to the
pan. Never allow
flames
to extend
beyond
the outer
edge of the pan.
Each burner
lights automatically
from
an electric
ignitor
each time
a control
knob
is turned
to the LITE position.
To operate
the surface
burner:
1.
Place cooking
utensil on burner.
2.
Push the Surface
Control
knob
in and turn counterclockwise
out of the
OFF position.
3.
Release the knob and rotate to the LITE position.
Note: All four electronic
ignitors
will click
at the same time.
However,
only the burner
you are
turning
on will ignite.
3.
Visually
check that
the burner
has lit.
4.
Push the control
knob in and turn
counterclockwise
to the desired flame
size. The control
knobs do not have to be set at a particular
mark.
Use the
guides
and adjust
the flame
as needed.
DO NOT cook with
the Surface
Control
knob
in the LITE position.
(The electronic
ignitor
will continue
to
click if left in the LITE position.)
Placement
of Burner
Caps
and
Trim
Rings
or Burner
Pans
(if
equipped)
1.
Place the trim rings or burner
pan over each burner,
matching
the ring size
with
the burner
size.
2.
Place the burner
cap on each burner,
again
matching
the cap size to the
burner
size. The caps for the Standard
Burner
and Power
Burners
have
locating
tabs that
align
with
slots
in the burner
base. The cap for the
Simmer
Burner
has an inner locating
ring which
locates the burner
cap in
the center
of the burner.
4.
Make sure each burner
cap is properly
aligned
and level.
5.
Turn the burner
on to determine
if it will light.
If the burner
does not light,
contact
an authorized
servicer.
Do not service the sealed
burner
yourself.
Burner Ca
Locatin(
Tabs
Burner Cap
Inner
Locating
Ring
I
I
_--_
Locating
I
Burner_
I
;
se
\
Standard
and
Power
Burners
I
Burner_
i
Simmer
Burner
if equipped
Advertisement
Table of Contents
