Advertisement
Turn controls and gas source or tank OFF when not
in use.
cAuTio.
if ignition does NOT occur in 5 seconds,
turn the
burner controls
OFF, wait 5 minutes and repeat the
lighting procedure,
if the burner does not ignite with
the valve open, gas will continue
to flow out of the
burner and could accidently
ignite with risk of injury,
Main Burner Match-Lighting
A Do not lean over grill while lighting.
1. Turn OFF all burner control valves.
2. Open lid during lighting. Turn on gas at LP cylinder.
3. Place match into match holder (hanging from side of cart).
Light match, and place into lighting hole for desired burner to
light. The lighting holes are located at the front of the cooking
grates between the emitter plate mounting brackets.
4. Push in and turn control knob to HI _
position for desired
burner to light. Be sure burner lights and stays lit.
5. If ignition does NOT occur in 5 seconds, turn the burner
Control knob off, wait 5 minutes for gas to clear away, and
repeat the match lighting procedure.
6. Ignite remaining burners by repeating steps 3 through 5 for
each burner.
Side Burner ignitor Lighting
A Do not lean over grill while lighting.
1. Open lid during lighting.
2. Turn ON gas tank valve.
3. Push and turn sideburner control knob to _
HI and
immediately press and hold ELECTRONIC IGNITION button.
4. If ignition does NOT occur in 5 seconds, turn burner control
knob OFF,wait 5 minutes for gas to clear away, and repeat the
lighting procedure.
5. Repeat above steps to light each burner individually.
Sideburner
Match Lighting
1. Turn OFF all burner control valves.
2. Open the sideburner lid.
Turn on gas at LP cylinder.
3. Place lit match near burner.
4. Turn sideburner knob to HI_
.
Be sure burner lights and stays lit.
WARNING: Sideburner
top cover must be open when
sideburner
is in operation.
8,464223210
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from Hi to LOW. You should see a smaller flame in
LOW position than seen on Hi. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
Turning Grill Off
• Turn all knobs to the OFF position. Turn LP cylinder OFF by
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic ignitor
button. "Click" should be heard and spark seen each time
between each collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
identical replacement part valve/hose/regulator as
specified in the Parts List of this Use and Care Guide.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted), Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
,A. Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill's high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
Advertisement
