GE GXSF27E Owner's Manual & Installation Instructions page 8

Water softening system
Table of Contents

Advertisement

Available languages

Available languages

Step-by-step installation instructions.
Programming the Control
CONTROL
SETTINGS
REQUIRED
upon installation
and
alter an extended
power outage.
NOTES:
::Ji:: X4_HEN THE T1L_tNSFORMER
IS PI,UGGED
INTO THE
EI,ECTRI(:AI,
OUTI,ET,
12:00 PM (flashing),
and PRESENT
TIME is displayed.
Program
tile control
as instructed
bel_m'.
If __--I_ -- -is flashing,
use tile Up •
button
to set tile
correct
model
code as fi)llo_vs: S1_2 fin" GXSF27E.
If wm
pass by tile correct
code nmnbe_;
use tile DOWN
i)utton.
Then
press the MODEbutton
to accept
the correct
model.
_: A "beep" sounds
while pressing
buttons
tor control
programming.
One beep signals a change
in the control
display: Repeated
beeps mean
tile control
will not accept
a change
ti'om tile button
you have pressed,
and you should
select another
button.
::Ji:: To program
tile control,
p)/i will tlse tile UP •,
DOWN
and
MOOEbuttons.
_: Use the MODEbutton
to select the desired
control
fimction.
SET PRESENT TIME OFDAY
I. Press tile MODEbutton
until PRESENT
TIMEappeax_ in tile display.
2. Press Lrp •
or DOWN
button
to set.
The UP button
ad\m_ces
tile time; tile
DOWN
button
inoves tile time in i'eveiNe.
_PM
U.CO
I'JO
PRESeNT'ME
I !.-IF'_
v30
PRESENT_M_
If tile present
time is between
noon
and midnight,
be sure
PM sho_vs in the display. If the present
time is between
midnight
and noon,
be sure _]
shows in tile display:
NOTE:Each press of an UP •
or DOWN
button
changes
the time bv one minute.
Holding
the button
changes
the time
at a rapid
rate.
3. \_]/en
the present
time is correct,
press MODE to accept.
SET WATERHARDNESS NUMBER
I. Pressthe MODEbutton until
HARDNESSappeax_ i n the display.
2. Press
UP
or DO_VN
button
to set your
water
hardness
nmnber
in tile display.
DOWN
decreases
tile hardness
xdue.
UP increases
tile hardness
xdue.
NOTE'Each press of a button
changes
tile display by 1, between
1 and 25. Above 25, the display changes
5 at a time (25, 30, 35,
etc.). Holding
a button
in changes
tile nulnbei_
at a rapid rate.
3. When
the display sho_vs yore" water hardness
(in grains per
gallon),
press MODEm accept.
NOTE."If there is dear water iron in your water supply, you will
need
to increase
the haacd_mss setting by 5 for each 1 ppm of
clear water iron in your water supply.
You cm_ get the grains per gallon
(gpg) haacd_mss of your water
supply
from a water m_aJysis laboratory.
If you are on a
municipal
supply,
call your local water department.
Or call
Legend
Tecl_fical
Services,
an independent
laboratory,
to
request
a water haaxlness
test kit at 1.800.826.8553,
extension
47. If your report
shows hamd_mss in parts
per million
(ppm)
or milligrmns
per liter (rag/l),
shnply divide by 17.1 to get the
equivalent
nmnber
of grains per gallon.
SET RECHARGE(STARTING) TIME
I
-_Hn
I-t
AM
I. Press the MODE button
until
l
_£_E!Ij
RECHARGE TIMEappea_
in tile display.
NOTE.'A flashing
2:00 _/I
(ii_cto_y delimit)
shouM
show in the display: This is a good time tot recharge
to start (takes about
2 houi_)
in most households
because
water
is not in use. HARD X_;_TER is b}passed
to house tinlcets
dm-ing rechmge.
If no chm_ge is needed,
go to step 3. To change
the rechmge
starting
time, tollow step 2.
2. Press UP •
or DOX4'N •
button
to set tile desired
rechaxge
start time. Be sure to observe
tile f_dVIor PM as w)u did when
setfng
the time ot day,
NOTE.'Each press of a button
changes
tile time by l horn;
Holding
tile buttons
in changes
tile time at a rapid
rate.
3. Press the MODE button
to accept.
8

Advertisement

Table of Contents
loading

Table of Contents