Cleaning Upholstery; Headlight Replacement; Lubrication; Storage - Hoover SteamVac F6026910 Owner's Manual

Table of Contents

Advertisement

Read
"Before
you
begin
cleaning"
instructions
on
page 9.
£e sure
to check
the cleaning
code
on
your upholstery.
Use your
deep
cleaner
only
on upholstery
marked
"W"
or
"W/S'.
1, Place
handle
in upright
position.
Agitator
brushes
will not rotate
while
handle
is in upright
position.
2. Fill clean solution
tank with HOOVER
Carpet/Upholstery
Detergent
according
to instructions
for Figs. 2a-8 to 2-1 4.
3. Attach
tool to end of hose.
Do not point
tools
toward
people
or
pets.
4. Dry hands
and plug deep
cleaner
into
a properly
grounded
outlet.
5. Turn deep
cleaner
ON. If necessary,
refer to "Before
using tool" section
to
remove
air from the system.
6. Gently
press the tool onto the fabric.
Press the trigger
and slowly
pull the noz-
zle over the fabric.
7. Overlap
strokes
by 1/2 inch to help
prevent
streaking.
Make additional
strokes
without
pressing
the trigger
to remove
more moisture.
8. To clean in corners
or creases,
lift the
tool one-half
inch from the fabric
and
press the solution
trigger.
The crevice
tool (included
in some
models)
is very
useful for this task.
9.Vacuum
up the solution
with the tool
without
pressing
the trigger.
10. For heavily soiled
areas,
it may be
-;
\f
necessary
to repeat
the cleaning
process.
Make crisscrossing
strokes
to
the original
pattern;
overlap
each pass.
Make
no more than
2 passes
with
the
solution
over any one area to prevent
over-wetting
and damage
to fabric.
If additional
cleaning
is necessary,
wait
until the upholstery
is completely
dry
before
using the tool again.
11. Empty recovery
tank when the motor
sound
becomes
higher
pitched
and
there is a loss in suction
(see "Automatic
shut-off",
Fig. 2-6).
When
finished
cleaning,
follow
"After
cleaning"
instructions on page 9 and
"After using tool" instructions
on page
12.
Headlight
replacement
What
to buy
The deep cleaner
uses a 7 volt, wedge
base type bulb, HOOVER
part no.
27313106.
Where
to buy
Bulbs
may be purchased
from autho
rized Hoover
dealers
(Depot),
Hoover
Factory
Service
Centers,
or through
The
Hoover
Company
online
at
www.hoover.com
How
to replace
Turn cleaner off and with dry hands,
disconnect deep cleaner from electri-
cal outlet,
1. Using a Phillips screwdriver, remove
the screw as shown and lift off lens.
2. Pull old bulb straight
out of socket.
3. Push new bulb straight
into socket until
locked
into place.
Excessive
force
is not required,
Reposition
lens and secure
with screw
Storage
Before
storing:
• Empty
solution
tank and rinse
thoroughly
with
clean wafer.
• Replace
empty
solution
tank
and
turn deep
cleaner
ON. Squeeze
trigger
and push
deep
cleaner
for-
ward and back several
times to
expel any solution
remaining
in the
deep cleaner's
system.
(Do not use
deep cleaner
on wood floors.)
• Empty
recovery
tank and rinse
thoroughly
with clean water.
Allow
brushes
and
underside
of deep
cleaner
to air dry thoroughly
before
storing deep
cleaner
on
a carpeted
or
wood
surface.
Do not store deep
cleaner
with a full
solution
tank
in place.
Lubrication
The motor
is equipped
with bearings
which
contain
sufficient
lubrication
for
the life of the motor.
The addition
of
lubricant
could
cause
damage.
Do not
add
lubricant
to motor
bearings,
13

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Steamvac f6025910Steamvac f6025

Table of Contents