Page of 60

Advertisement

Installation
Instructions
SET WATER HARDNESS NUMBER (CONT.)
3. When the displag shows gour water hardness
(in grains per gallon), press MODE to accept.
NOTE: If there is clear water
iron in your water
supply,
you will need to increase the hardness
setting
bg 5 for each 1 ppm of clearwater
iron
in your water
supply.
You can get the grains
per gallon (gpg} hardness
of your water
supply from a water analysis
laboratory.
If you are on a municipal
supply,
call your local water department.
Or call Legend
Technical
Services, an independent
laboratory,
to request a water
hardness
test kit at
1.800.949.8220,
option
4. If your report
shows
hardness
in parts per million
(ppm) or milligrams
per liter (rag/I), simply divide
by 17.1 to get the
equivalent
number
of grains per gallon.
SET RECHARGE (STARTING) TIME
1. Press the MODE button until
r
RECHARGE TIME appears
in the
/
_-I.rll-I
"M
d isplag,
k.................................
_°;_i:u .............................
NOTE: A flashing 2:00 AM (factorg
default) should show in the displag. This is a good
time for recharge
to start (takes about 2 hours)
in most households
because water is not in use.
HARD WATER is bgpassed to house faucets during
recharge.
If no change
is needed, go to step 3. To change the
recharge
starting time, follow step 2.
2. Press UP •
or DOWN •
button to set the desired
recharge start time. Be sure to observe the AM or
PM as gou did when setting the time of dag.
NOTE: Each press of a button changes the time bg
1 hour. Holding the buttons in changes the time at
a rapid rate.
3. Press the MODE button to accept.
11
OPTIONAL CONTROL SETTINGS
The controller displag has several options and
features.
SYSTEM/ELECTRONIC
DIAGNOSTICS
This display contains
system
diagnostics
information
to assist in
troubleshooting
problems with the
Water Softener. See page 17.
nnn
P
!_1 IJ LJ --
OR
To access the Sgstem Diagnostics,
press and hold
the MODE button for 3 seconds.
To return to the normal displag, press the MODE
button 2 times.
SALT EFFICIENCY
When the SALT EFFICIENCY feature is ON, the
unit will operate
at a salt efficiencg
of at least 4000
grains of hardness removed per pound of salt. This
mode of operation
is the most efficient setting for
salt usage, because the sgstem will tend to recharge
more often, with less salt usage. Turning the feature
OFF will tend to lengthen
the time between
recharge
cgcles, which will provide the most efficient usage
of water, but nag use more salt. The degree of
difference
between these two cgcles is highlg
dependent
on the water usage and hardness
at a particular
installation.
NOTE: California Regulations
require this feature to
be ON for installations
in California.
To access the Salt Efficiencg,
press and hold the MODE
button for 3 seconds. The Sgstem
Diagnostics
displag will appear.
Press the MODE button
again
and
the Salt Efficiencg displag will
appear.
LT,-,
NCC
urr
To change the setting, press the
UP
or DOWN •
buttons to toggle the feature
ON or OFK Press the MODE button to accept.
ERROR SIGNALS
If there is an error code detected,
the displag will flash Err to signal
that the softener requires service.
Er rl] I
See page Z6 for information
to
assist in troubleshooting
error codes. Once the
problem
is corrected,
disconnect
the transformer
from the wall outlet momentarilg,
and plug it back
in. The normal displag will appear. The motor mag
run for several minutes, as the unit resets. If the
problem
is not corrected,
the error code will
reappear
in 6 minutes.

Advertisement

Comments to this Manuals

Symbols: 0
Latest comments: