Related Manuals for Eden World Tour WT1250
Summary of Contents for Eden World Tour WT1250
- Page 1 THE LEADER IN BASS AMPLIFICATION. World Tour Amplifier High Power Bass Guitar Amplifier Models WT1250 and WT1550 Never Compromise™ ©02-23-2006 by U.S. Music Corp.
- Page 2 The Eden World Tour products group is the result of our quest for ultimate bass tone and maximum reliability. Your new Power Amplifier features our latest input section, using dual pre-amp tubes to provide unequaled warmth and tonal adjustment to accommodate varying room acoustics.
- Page 3 The Eden line of World Tour amplifiers is the result of our research and development in combining high performance and compact size. Just as a skilled craftsman needs good quality tools that won't let him down on the job, so does a good musician. We hope you enjoy the tool we’ve created for you.
- Page 4 GENERAL SPECIFICATIONS WT1550: Size 3.5” x 19” x 14.5” Weight 32 Lbs. EIA rack 2 Space w/ min. clearance Power Output @ 8Ω: 2 x 300 Watts RMS; @ 4Ω: 2 x 600 Watts RMS; @ 2Ω: 2 x 750 Watts RMS (Both channels driven) Bridge Mode @ 8Ω: 1200 Watts RMS;...
-
Page 5: Front Panel Features
Power Requirements – The WT1250 needs a separate properly grounded 20 Amp circuit @ 120 Volts for correct operation and best sound quality. FOR YOUR SAFETY DO NOT REMOVE OR MODIFY THE GROUND ON YOUR POWER CABLE. Fuse Requirements USA @ 120 Volts /60 HZ - 12 Amps, 5 x 20 mm GMC/T/slow blow Europe @ 240 Volts/50 Hz - 6 Amps, 5 x 20 mm GMC/T/slow blow Japan @ 100 Volts/60 Hz - 14 Amps, 5 x 20 mm GMC/T/slow blow Operation and Power Requirements –... -
Page 6: Back Panel Features
These controls are very useful in rooms with unusual or bad acoustic characteristics. For example in a room that is very dead or over damped, raising the treble level will allow the Bass to cut though better. If the room has too much bass the same solution will be helpful. - Page 7 Fuse Holder –To access the fuse, unscrew the fuse holder cap, which is located near the power cord. The fuse is selected for the country of operation (see list at front of manual). USE ONLY THE SAME SIZE AND TYPE FOR REPLACMENT.
-
Page 8: Operating Instructions
Thermal Protection System – Your World Tour amplifier has a fully automatic thermal safety system that will automatically reduce the output power available as needed to maintain best possible operations under sever operating conditions. Both channels operate independent of each other. Cooling System –... - Page 9 Connections – Line connections (everything but the speakers) should be made with high quality shielded cables. The use of speaker cables for line connections will result in excess noise. Speaker connections should be made with high quality 16 gauge or larger unshielded speaker cables. We recommend 10 or 12 gauge cables.
- Page 10 Once you’ve ensured that all connections are correct, turn the unit ON. Turn the Input Gain up to a level that matches your preamplifier. If necessary, use the tone controls to quickly equalize your system to any room anomalies. A FEW TECHNICAL THINGS TO REMEMBER Clipping = Bad –...
-
Page 11: Other Considerations
YOU’RE DONE. GO PLAY. There you have it: a quick and easy process to help you set up your Eden amplifier. It may take an extra minute or two to ensure everything is connected correctly. However, doing so will ensure that you don’t damage any equipment. - Page 12 DO NOT continue to use the amplifier in this condition. Learn More – If you’d like to learn more about your amplifier (or about our company and its activities), we invite you to visit our website – www.eden- electronics.com. There you’ll find articles to help you better understand our products and the technical stuff some people find so interesting.