Led Functions Of Charger; Charging A Hot Battery Pack; Charging A Cold Battery Pack; Defective Battery - Craftsman nextec 320.10003 Operator's Manual

12.0-volt lithium-ion cordless 3/8 in. reversible drill
Table of Contents

Advertisement

LED FUNCTIONS
OF CHARGER
(Fig. 3)
BATTERY
RED
GREEN
LED INDICATOR
ACTION
PACK
LED
LED
Charging
will begin
HI/LO TEMP.
Hot/Cold
On
Off
when battery returns to
(SEE
MANUAL)
battery
32°F (0°O)-104°F
(40°0)
DEFECTIVE _
Battery pack or
BATTERY
Defective
Flashing
Off
Charger/Adapter
is
defective
BATTERY
_
Charging
Off
Flashing
Charging
CHARGING
BATTERY
_
Fully
Charging
is complete
FULL
charged
Off
On
Maintenance
charging
CHARGING A HOT BATTERY PACK
If the battery pack is above normal temperature
range, the red LED will illuminate
and the green LED will be off. When the battery pack cools down to approxi-
mately 104°F (40°C), the charger will automatically
begin charging.
CHARGING A COLD BATTERY PACK
If the battery pack is below the normal temperature
range, the red LED will illu-
minate and the green LED will be off. When the battery warms to a temperature
of more than 32°F (0°C), the charger will automatically
begin charging.
DEFECTIVE BATTERY
If the charger detects
a problem,
the red LED will begin flashing
and the green
LED will be off.
1.
2.
3.
If registering
as defective,
remove and reinsert the battery
pack in the charg-
er. If the LED status reads "defective"
a second time, try charging a different
battery
pack.
If a different
battery
pack charges
normally,
dispose
of the defective
battery
pack (see Maintenance
section).
If a different
battery
pack also indicates
"defective,"
the charger may
be defective.
BATTERY CHARGING
If the battery pack is being charged within a normal surrounding
temperature
range (32 F to 104 F), the green LED will begin flashing
and the red LED will be
off. The battery pack will reach a full charge
in 30 minutes.
BATTERY FULL
If the battery pack is within normal temperature
range, the green LED will illuminate
and the red LED will be off. The battery pack is fully charged and ready to use. The
battery pack will fully charge, but will not overcharge,
if left on the charger.
NOTE: Charger may warm with several continuous
charge cycles. This is part of
the normal operation
of the charge. Charge in a well ventilated
area.
TO ATTACH BATTERY
PACK (Fig. 4)
1.
Make sure that the Drill
is "OFF"
2.
Align the raised rib on
the battery
pack with the
grooves of the Drill, and
then attach the battery
pack to the Drill.
NOTE: Make sure that the latch
on the battery
pack snaps into
place and the battery
pack
is secured to the tool before be-
ginning operation.
Fig. 4
/
t
TO DETACH BATTERY PACK (Fig. 4)
1.
Lock the trigger switch on the Drill by placing the direction
of rotation (for-
ward/reverse/center
lock) selector
in center position.
2.
Depress the battery release buttons
located on the both sides of the battery
pack to release the battery pack.
3.
Pull the battery
pack out and remove it from the tool.
CAUTION:
When placing the battery pack in the tool, be sure that the
raised rib on the battery
pack aligns with the groove
inside the Drill and the
latches snap into place properly.
Improper
assembly
of the battery pack can
cause damage to internal components.
_L. WARNING:
Battery tools are always in operating
condition.
Therefore,
the direction-of-rotation
selector
should always be locked when not in use or
carrying
at your side.
10003
ManuaLRevised_08
0724
Page 18
10003
ManuaLRevised_08
0724
Page 19

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents