Download Print this page

Craftsman 315.113861 Operator's Manual page 5

3/8 in., 18 volt drill variable speed/reversible

Advertisement

,_
WARNING!
READ AND UNDERSTAND ALL
INSTRUCTIONS.
Failure to follow aii instructions
listed below, may result in electric shock, fire
and/or serious personal injury.
[] Before using battery charger,
read all instructions
and cautionary markings in this manual, on battery
charger, battery, and product using battery to prevent
misuse of the products and possible injury or damage.
_1_
CAUTION:
To reduce the risk of electric shock
or damage to the charger and battery, charge only
nickel-cadmium
rechargeable batteries as specifi-
cally designated on your charger. Other types of
batteries may burst, causing personal injury or
damage.
[] Do not use charger
outdoors
or expose to wet or
damp conditions.
Water entering charger will increase
the risk of electric shock.
[] Use of an attachment
not recommended
or sold
by the battery charger
manufacturer
may result in
a risk of fire, electric
shock, or injury to persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
[] Do not abuse cord or charger.
Never use the cord to
carry the charger. Do not pull the charger cord rather
than the plug when disconnecting
from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords im-
mediately.
[] Make sure cord is located so that it will not be
stepped
on, tripped
over, come in contact with
sharp edges or moving parts or othent_ise subject-
ed to damage
or stress. This will reduce the risk of
accidental falls, which could cause injury, and damage
to the cord, which could result in electric shock.
[] Keep cord and charger
from heat to prevent
damage to housing
or internal parts.
[] Do not let gasoline,
oils, petroleum-based
products,
etc. come in contact with plastic
parts. They contain
chemicals that can damage, weaken, or destroy plastic.
[] An extension
cord should
not be used unless
absolutely
necessary.
Use of improper extension cord
could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
NOTE: AWG = American Wire Gauge
[] Do not operate
charger with a damaged
cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
[] Do not operate
charger
if it has received a sharp
blow, been dropped,
or otherwise
damaged
in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
[] Do not disassemble
charger. Take it to an authorized
serviceman when service or repair is required. Incor-
rect reassembly may result in a risk of electric shock or
fire.
[] Unplug charger
from ouUet before attempting
any
maintenance
or cleaning to reduce the risk of
electric
shock.
[] Disconnect
charger
from the power supply when
not in use. This will reduce the risk of electric shock
or damage to the charger if metal items should fall into
the opening. It also will help prevent damage to the
charger during a power surge.
[] Risk of electric
shock.
Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
[] Save these instructions.
Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instruc-
tions also to prevent misuse of the product and
possible injury.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction
activities
contains chemicals known to cause cancer, birth defects or other reproductive
harm. Some examples of these
chemicals are:
• lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic
particles.

Advertisement

loading