Download Print this page

Advertisement

Installation
Instructions
SET WATER HARDNESS NUMBER (CONT.}
3. When the display shows your water hardness
(in grains per gallon), press MODE to accept.
NOTE: If there is clear water
iron in your water
supply,
you will need to increase the hardness
setting
by 5 for each 1 ppm of clear water iron
in your water supply.
You can get the grains
per gallon (gpg}
hardness
of your water supply from a water
analysis
laboratory.
If you are on a municipal
supply,
call your local water department.
Or
call Legend Technical
Services, an independent
laboratory,
to request a water hardness
test kit
at 1.800.949.8220,
Option 4. If your report
shows
hardness
in parts per million
{ppm} or milligrams
per liter (my/I}, simply divide by 17.1 to get the
equivalent
number
of grains per gallon.
SET RECHARGE (STARTING} TIME
AM
:,.nOl
i
i. Press the MODE button
t_l
C.uu
until arrow I_ points to
RECHARG E TI M E.
I _|
RECHARGE
I
) TIME
NOTE: A flashing 2:00 AM
(factory default) should show in the display. This is e
good time for recharge to start (takes about 2 hours)
in most households
because water is not in use.
HARD WATER is bypassed
to house faucets during
recharge.
If no change
is needed, go to step 3. To change the
recharge starting
time, follow step 2.
2. Press UP •
or DOWN •
button to set the desired
recharge start time. Be sure to observe the AM or
PM as you did when setting the time of day.
NOTE: Each press of u button changes the time by
1 hour. Holding the buttons in changes the time at
a rapid rate.
3. Press the MODE button to accept.
SET SALT LEVEL
i. Press the MODE button
It_1
m m
,.] SALTLEVEL
until arrow I_ points to
[
u.u
]
SALT LEVEL.
2. Determine
level of salt in
brine tank using yellow indicator on side of brine
well, inside brine tank (see illustration
on page 5).
.
Press UP •
or DOWN •
button to set the SALT
LEVEL to correspond
to
level on yellow indicator
in brine tank.
SALT
I I h'_
_]
SALT LEVEL
.....
-t. 3
J
NOTE: Each press of e button changes the
level by increments
of 0.5 up to 8.0. As the number
increases, the suit level burs increase on each whole
number. Lowering the suit level below zero turns the
SALT LEVEL indicator OFF.
4. Press the MODE button to
accept. The display shows the
present time of day end DAYS
TO EMPTY. RECHARGE TONIGHT
may appear if unit is new.
3._nl
I
DAYS TO EMPTY
The words DAYS TO EMPTY and o
rSALTI 3. i nl 1
number
are shown t he ,ower
ha,f
I ..... I
of the display. T hisinformation is
Iml
i -I- -
I
I
shown inthe normal run display.
LEI
J
This is to inform the user of the
number of days before the suit level in the brine
tank reaches Level 0. There will be suit left in the salt
tank, but it mug not be sufficient
to fully recharge
the system. Suit should be added at this time to
avoid hard water. The value is updated daily and
whenever the SALT LEVEL value is changed.
NOTE: For the first several weeks of operation,
the
DAYS TO EMPTY may provide erratic operation.
For
example, the blue indicator
light may flash, showing
that more salt is required when the actual salt level
in the tank is well above the Level 0. In some cases,
the DAYS TO EMPTY may even increaseover a
severalweek period.
It takes a couple of months for the water softener to
learn your water usage pattern. Once it does this, it
will accurately
determine
actual salt usage pattern.
During this first period, check salt level when blue
indicator
light flashes. If the salt level in the tank is
at Level 1 or above, allow system to run. Be sure to
reset your salt level indicator each time you add salt
to the system.
ll

Advertisement

Comments to this Manuals

Symbols: 0
Latest comments: