Craftsman ZTS 7500 Operator's Manual page 17

107.249210 2-bin bagger
Hide thumbs Also See for ZTS 7500:
Table of Contents

Advertisement

Available languages

Available languages

Figure15 continued...
A. HitchSupportAssembly
B. BagandCoverSupportAeeembty
C. ShoulderBolt
D. Mount Pin
E. Retainer Spring
F. Hinge Pin
G. Retainer Spring
H. Cover Hinge Pivots
I.
Cover
J. Bag
K. Bag Hanger
L. Ridge Cutout
mnstaHation
NOTE." See previous pages for more detailed installation
and operation instructions if necessary.
1. Attach bag and cover support assembUy
(B, Figure 15) to hitch support assemMy (A)
by sliding the support mount (Y) into pUace until full
contact is made with the shouUder bouts (C).
2. insert mount pin (D) through support mount (Y) and
upright of hitch assemMy (A).
3. Secure mount pin (D) with retainer spring (E).
4. Attach cover assembUy (U)to bag support assembly
(B) using cover hinges pivots (H). Secure cover
assembly (I) to bag support bracket (B) using hinge
pins (F) and retainer springs (G).
5. Raise the cover (I), and attach collector bags (J)
using grass bag hanger (K) to hanger post
(D, Figure 7).
6. Lift discharge deflector (V, Figure 15) up, and insert
front latch plate (S) into front latch plate mount (T).
7. Swing lower chute (R) into place below discharge
deflector (V) placing hob in lower chute over carriage
bolt (W).
8. Stretch rubber strap (U) down to the rear latch plate
mount bolt (X) attaching the first hob in the rubber
strap over the mount bolt.
9. Slide upper tube (M) into cover (I) aligning ridge (N)
with ridge cutout (L).
10. Slide tube assembly (0) over lower chute (R)
securing tube assembly (0) to lower chute (R) using
rubber strap (P) on tube assembly (0) to pin (Q) on
lower chute (R).
M. Upper Tube
N. Ridge
O. Tube AeeemMy
P. Rubber Strap
Q. Pin
R. Lower Chute
S. Front Latch Plate
T. Front Latch [Vlount
U. Rubber Strap, Lower Chute
V. Discharge
Deflector
W. Carriage
BoJt
X. Rear Latch Plate IVlount Bolt
Y. Support
Mount
WARNING
OPERATION WITHOUT BAGGER
For operation without bagger, the mower discharge
deflector blUST be properly installed in the DOWN
position and retained by the spring latch.
Remova_
1. Unhook rubber strap (P, Figure 15) from pin (Q), then
remove tube assembly (0) from lower chute (R) and
from cover (I).
2. Lift cover (I) and remove bags (J) from bag and cover
support assembly (B).
NOTE: Support the cover during the next step.
3. Remove cover (I) by disconnecting
retainer springs
(G), then remove both hinge pins (F).
4. Remove bag and cover support assembly (B) from
hitch assembly (A) by removing retainer spring (E),
then removing mount pin (D).
NOTE:
To prevent loss of pins and retainer springs
re-attach them to the cover, and bag and cover support
assembly.
5. Disconnect lower chute rubber strap (U, Figure 15)
from rear latch plate mount bolt (X).
6. Lift up discharge deflector (V, Figure 15); remove
lower chute (R) from carriage bolt (W), then remove
front latch latch plate (S) from front latch mount (T).
IMPORTANT:
See that discharge deflector (R) returns to
the DOWN position.
17

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

107.249210

Table of Contents