Advertisement
o
i
TOOLS
NEEDED
Screwdriver
[medium)
3!8-inch
wrench
7/!6*inch
wrench
UNPACKING
AND CHECKING
CONTENTS
This
Craftsman
welder
is shipped
complete
in one carton.
In order
to
facilitate
packaging,
certain
items
have
been
removed
at
the
factory,
and
must
be assembled
when
received
by the purchaser.
Remove
all items from the loose
parts bag and identify
them
by referring
to figure
I. These
"'Loose"
parts are listed
below
and should
be accounted
for
before
discarding
any packing
material.
(See figure
1.)
!
2
/
4
LOOSE PARTS LIST
Key No.
(Fig, !) Part I_ame
1
2
3
4
Figure
t
Sty.
Welding Helmet {Partially
assembled).,
i ........
1
Owner's Manual: ......
, ......
...............
I
Helmet band assembly ......................
1
Loose Parts Bag
-Containing
the following
items:
Electrode H01der ... : : ....................
1
Ground c_amp. ..................
. ... ....
1
Receptacle .............
_.......
.. .......
t
Screw, Hex.-Hd., 1/4-20 x 3/4 in .............
t
Nut, Hex,, 1/4-26
........................
t
Washer, Rat, 17/64 in .......
:...
_/.:
......
I
L0ckwasher,
t/4 in........................
I
ATTACHING
ELECTRODE
HOLDER
TO ELECTRODE
CABLE
1. Grasp the electrode holder and locate the slotted-head,
handle iocking screw near the mid-point
of the insulating
handle
tube.
(See figure
2.)
Loosen
this
screw
approximate|,/two
turns, until the handle can be slipped
off the electrode holder.
2. Slide
the handle
off electrode
holder
and insert
end of
electrode
cable assembly
through
the handle
as shown
in
3.
4.
.
6.
figure
2.
The
electrode
cable
is
the
one
with
approx
mately
1/2-inch
of the
insulation
stripped
from
One end.
Using a screwdriver,
back out the stetted-head
set screw,
_ocated
near the end of electrode
holder
until
the end of
screw does not protrude
into
the wire socket
in the end
of holder.
Make sure the wire
strands on stripped
end of electrode
cable
have
not
been
"fra,/ed',
Twist
together
with
fingers
if necessary.
Insert
stripped
end of electrode
cable into the electrode
holder
and tighten
the slotted-head
set screw firmly,
Slide
the handle
back into
place on electrode
holder
and
position
it until
the
hote
in handle
is directly
over the
head
of
handle
locking
screw.
Tighten
the screw
just
enough
to secure the handle
on electrode
holder.
ATTACHING
THE GROUND
CLAMP
TO THE GROUND
CABLE
Attach
the
terminal
on
end
of ground
cable
to
the
ground
clamp,
at the hole
near the nose of the clamp,
with
the 1/4-20
x 3/4-inch
screw,
!/4-20
nut,
17/64-inch
flat
washer
and
1!4-inch
lockwasher
furnished
in
the
loose parts bag. (See figure
3.)
SCREW
NUT \_,
Figure
3
GROUND
CABLE
DO
NOT
USE
THESE HOLES
2. Do not use either
of the holes in hand!e
ends of ground
clamp.
3. Tighten
the screw
firml,/
enough
to insure
good contact
and
prevent
the
cable
termina!
from
s!ipping
on the
clamp.
Advertisement
