Changing Cooktop And/Or Oven Lights - Frigidaire FEF355BFWB Owner's Manual

Hide thumbs Also See for FEF355BFWB:
Table of Contents

Advertisement

Changing
Cooktop
and/or
Oven Lights
(some
models)
Be sure the range
is unplugged
and all parts are COOL before
replacing
the surface
or oven lights. Wear a leather-faced
glove for protection
against
possible
broken
glass.
To Change
the
Cooktop
Light
(some
models)
1.
Turn power
off at the main source
or unplug
the range.
2.
Remove
Phillips®
Head screws (2) that
secure the light cover and then
lift
the light
cover off.
3.
Remove
bulb by rolling
back and up. Install the new bulb by sliding
down
and rolling
forward
into place.
4.
Re-install
light cover and secure with
Phillips®
Head screws (2).
To Change
the
Oven
Light
(some
models)
On some
models,
the
oven
light
automatically
turns
on when
the door
is
opened.
Some models
have a switch
located
on the control
panel to turn on
the light.
The oven light
is located
at the rear of the oven and is covered
with
a glass shield held by a wire holder.
The glass shield must be in place whenever
the oven is in use.
To replace
the oven
light:
1.
Turn electrical
power
off at the main source
or unplug
the range.
2.
Press wire holder
to one side to release the glass shield.
3.
Replace
bulb with
a new 40 watt
appliance
bulb.
4.
Replace
glass shield
over bulb
and snap wire
holder
into place.
5.
Turn power
back on again at the main source (or plug the range
back in).
6.
The clock(if
equipped)
will then
need to be reset. To reset, see Setting
the
Clock
and
Minute
Timer
in this Owner's
Guide.
Adjusting
Oven
Temperature
Note: The adjustments
made will not
change the se f-c ean ng temperature.
The temperature
in the oven has been set at the factory.
When first using the
oven,
be sure to follow
recipe times
and temperatures.
If you think
the oven
is too
hot or too cool,
the temperature
in the oven
can be adjusted.
Before
adjusting,
test a recipe by using a temperature
setting
that
is higher
or lower
than
the recommended
temperature.
The baking
results
should
help you to
decide
how much
of an adjustment
is needed.
To Adjust
Oven Temperature:
1.
Push (/_.
2.
Set the temperature
to 550°F (287°C)
by pushing
and holding
the [/_.
3.
Within
2 seconds,
push
and hold
(_
until
the special
2 digit
display
appears.
Release ('_.
The display
now indicates
the amount
of degrees
offset
between
the original
factory
temperature
setting
and the current
temperature
setting.
If the oven control
has the original
factory
calibration,
the display
will
read "00."
4.
The temperature
can now be adjusted
up or down
35°F (17°C), in 5°F (1°C)
steps, by pushing
and holding
the _
or _.
Adjust
until the desired
amount
of offset
appears
in the display.
When
lowering
the
oven
temperature,
a minus
sign (-) will appear
before
the number
to indicate
that
the oven will
be cooler
by the displayed
amount
of degrees.
5.
When you have made the desired
adjustment,
push _
to go back to the
time
of day display.
17

Advertisement

Table of Contents
loading

This manual is also suitable for:

Fef355bfwcFef355bfwdFef355bfwaFef355bfwe

Table of Contents