Download Print this page

Location Of Washer; Electrical Requirements - Whirlpool 3948875 Installation Instructions

240-volt 50-hz washer

Advertisement

Location
of washer:
Check location
where washer will be installed. Make sure you have everything
necessary
for correct installation.
Proper installation
is your responsibility.
-
Hot and cold water
Efaucets:
Must be
wrthrn 122cm (4 feet)
of the back of the
washer and provide
water pressure
34.51200
kPa
Water
heater:
Set to
deliver 60°C (140°F)
This washer may be installed
in a recessed area or closet.
The installation dimensions shown
and bottom of door are required.
are the minimum
spaces
Louvered doors with air openings
allowable. Additional
spacing
in top and bottom are
should be considered for ease of
acceptable.
installation and servicing.
Companion
appliance spacing
If closet door is installed, the
should be considered.
minimum
air openings in top
Minimum
installation
spacing
*Additional
clearances
for wall, door and floor
moldings
may be required.
Earthed
electrical
outlet
is required. See
"Electrical requirements,"
Panel A.
The hot and cold water
inlets on the back of the
washer have 314 -
11-l /2
American hose coupling
standard threads.
i
7.&m
(3")
155 sq. cm
(24
sq. in.)
Important:
Observe
all governing
codes and ordinances.
I
Support:
Floor must be
sturdy enough to support
washer weight of 143kg
i
7.6cm
(3")
35.6
cm
max.
(14"
max.)
cm
min.
Level floor:
Maximum
slope under entire washer -
25cm (1 inch).
Do Not store or operate
washer
below
0°C (32'F)
(some water
may remain
in washer).
See Use & Care Guide for "Winterizing"
information.
Ocm
W")
Untape and open washer lid. Remove packages, hoses and literature rack from washer.
1. Laundry
tub drain
system:
2. Floor drain
system:
3. Standpipe
drain
system:
Needs a 76-liter (20-gallon)
laundry tub.
Needs a 51 -mm (two-inch)
minimum
diameter standpipe
with minimum
carry-away capacity of 64
Floor standpipe
drain
/
Top of
stand
ipe
must ii e at
least 86cm
(34 inches)
high and no
higher
than
183cm
I
72 inches)
rom bottom
of washer.
A
7
Top df tubmust
1 ,
be at least 86cm
(34 inches) high
and no hiaher
I
86cm
--_...
(34 inches) min.
183cm
!
72 inches) max.
rom end of
drain hose to
bottom
of
than 183&n
/
(72 inches)
washer.
0
If a longer drain hose is needed, use drain hose extension kit (Part No. 285702). If drain hose must be shortened,
use kit (Part No. 285442).
Both kits are available from Whirlpool-authorized
parts distributors,
Electrical
requirements
Recommended
earthing
method
alI
Electrical
earth
is required
Do Not use an extension
cord
on this appliance.
with
this appliance.
DO Not earth
to a gas pipe.
Do Not have a fuse in the
Do Not change
the power
neutral
or earthing
circuit.
*
supply
cord plug.
if it does
not fit the outlet,
have a
Check with
a qualified
electrician
if you are in doubt
proper
outlet
installed
by
as to whether
the appliance
is
a qualified
electrician.
properly
earthed.
Failure
to follow
these
instructions
could
result
in
death
or serious
injury.
if codes permit
and a separate
earthing
wire
is used, it is
A 240~volt, 50-Hz, 8-amp, fused electrical
recommended
that
a qualified
supply is required. Time-delay fuse or
circuit breaker is recommended.
It is
electrician
determine
that
the
earthing
path
is adequate.
recommended
that a separate circuit
serving only this appliance be provided.
round earthing-
type wall receptacle
earthlng
PM
Figure
1
For your personal safety, this appliance
must
be earthed. This appliance is equipped
with a
power supply cord having an earthing plug.
If the power supply cord of this washer is
damaged,
it must be replaced by a special
cord, (Part No. 3353308),
available from the
dealer from whom you purchased the washer,
or an authorized
Whirlpool
service company.
To minimize possible shock hazard, the cord
must be plugged into a mating earthing-type
wall receptacle, earthed in accordance with
local codes and ordinances. If a mating wall
receptacle is not available, it is the personal
responsibility
and obligation
of the customer
to have the proper earthed wall receptacle
installed by a qualified electrician.
See Figure
Panel A
1 to determine
the proper mating wall
receptacle for the power supply cord plug

Advertisement

loading