Tuning To The Nextprogrammed Channel; Tuningto A Specific Channel (Programmed Or Unprogrammed); Switching Between Two Channels Using Surllock 1; Selecting Tile Picture Size - Toshiba 40G300U Owner's Manual

Tuning to the nextprogrammed
channel
To tune to the next programmed channel:
CH
Press (_ or _ on the remote control or TV control
panel.
Note: This feature will not work unless you
program channels into the TV's channel memory
(_, page 31).
Tuningto a specific channel
(programmed or unprogrammed)
Tuning analog channels:
Press the Channel Number (0-9) on the remote
control. For example, to select channel 125, press 1,2,
5, then @.
Tuning digital channels:
Press the Channel Number (0-9) on the remote
control, followed by the dash ((_)) button and then
the sub-channel number. For example, to select digital
channel 125-1, press i, 2, 5, -, 1, then @.
Note: If a digital channel is not programmed--
either through the automatic channel scan (_
page 31) or the Channel add function (_ page
32)--you will have to tune the RF channel using
the Channel Number and dash ((_)) on the
remote control.
Switchingbetweentwo channels
usingChannelReturn
The Channel Return feature allows you to switch
between two channels without entering an actual
channel number each time.
1 Select the first channel you want to view.
2 Select a second channel using the Channel
Number buttons (and the dash ((_) button if
selecting a digital channel).
CH RTN
3 Press
0
on the remote control. The previous
• . . CH FITN
channel will &splay. Each nine you press O , the
TV will switch back and t_rth between the last two
channels that were tuned.
CH RTN
Note: If you press 0 from a non-antenna
input, the TV will return to the last-viewed
input.
Switchingbetweentwo channels
usingSurfLock
TM
The SurfLock
TM
feature temporarily "memorizes" one
CH RTN
channel to the O button, so you can return to that
channel quickly from any other channel by pressing
OH RTN . CH RTN
O • To memorize a channel to the O button:
1 Tune the TV to the channel you want to program
CH RTN
into the O button.
OH RTN .
Press and hold O for about 2 seconds until
the message "Memorized" appears on-screen.
The channel has been programmed to the CH(_'m
button.
3 You can then change channels repeatedly, and
CH RTN
when you press O , the memorized channel
will be tmled.
The TV will return to the memorized channel one
CH RTN
time only. Once you press O and then change
channels again, the CH RTN memory will be cleared
and the button will function as Channel Return,
by switching back and forth between the last two
channels that are tuned.This feature also works for
external inputs.
SelecUng the picture size
You can view many program formats in a variety of
picture sizes--Natural,
ThealerWide 1,ThealerWide
2, TheaterWide 3,Full, 4 :3HB,Native, a ndDot
by
Dot
(available in PC Mode Only).
Note: The "picture size" illustrations are
examples onl)_ The format of the image (in any
of the picture sizes) will vary depending on the
format of the signal you are currently watching.
Select the picture size that displays the current
program the way that looks best to you.
You can save separate picture size preferences for
each input on your TV.
To select the picture size using the remote
control:
1
2
PIG SIZE
Press 0 on the remote control.
While the
Picture Size
screen is open, you can do
one of the following to select the desired picture
size:
PIG SIZE
• Repeatedly press O •
,, Press the corresponding Number button (0-6)
while the
Picture Size
screen is open.
,, Press & or Y while the
Picture Size
screen is
open.
(comim_erl)
39