Panasonic WV-CP300 Operating Instructions Manual
Color cctv camera
Hide thumbs
Also See for WV-CP300:
- Preliminary (2 pages) ,
- Installation manual (32 pages) ,
- Operating instructions manual (27 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Operating Instructions
Color CCTV Camera
WV-CP310, WV-CP314
Model No:
WV-CP300, WV-CP304
This illustration represents WV-CP300.
Lens: Option
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Advertisement
Table of Contents
Related Manuals for Panasonic WV-CP300
Summary of Contents for Panasonic WV-CP300
-
Page 1: Operating Instructions
Operating Instructions Color CCTV Camera WV-CP310, WV-CP314 Model No: WV-CP300, WV-CP304 This illustration represents WV-CP300. Lens: Option Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. -
Page 2: Preface
Preface About the user manuals The operating instructions of the camera consist of 2 sets: these operating instructions (PDF) and Installation Guide. This document explains how to configue the settings of the camera. Refer to the installation guide for further information about how to install the camera. ®... -
Page 3: Table Of Contents
Contents Preface ............................2 About the setup menus ........................ 4 List of setup menu ........................4 Basic operation ..........................5 CP310 Screen transition diagram ....................7 CP310 CP310 Screen transition diagram ....................8 CP300 CP310 Camera title setting [CAMERA ID] ....................9 CP300 Camera operation setting [CAMERA SETUP] ................ -
Page 4: About The Setup Menus
About the setup menus Performing each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each item in accordance with the conditions of the camera shooting area. List of setup menu Setup item Description This item specifies the camera title. -
Page 5: Basic Operation
Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor. The description below explains how to operate the setup menu basically. Screenshots of WV-CP310 are shown as an example. Screenshot 1 Step 1 Hold down the [SET] button for about 2 sec-... - Page 6 Screenshot 3 Step 4 The selected setup screen in the setup menu appears on the screen. Perform the settings for each item. • Selection of setting item: Press the [UP] button or [DOWN] button **CAMERA SETUP** SCENE1 to move the cursor. ALC/ELC SHUTTER •...
-
Page 7: Screen Transition Diagram
Screen transition diagram CP310 CP310 Top screen “CAMERA ID” screen CP300 MODEL WV-CP310 SERIES **CAMERA ID** CAMERA ID 0123456789 CAMERA ABCDEFGHIJKLM SYSTEM NOPQRSTUVWXYZ SPECIAL ().,'":;&#!?= LANGUAGE +-*/%$ SPACE POSI RET TOP END RESET ....SETUP DISABLE “CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC SHUTTER... -
Page 8: Screen Transition Diagram
CP310 CP310 Screen transition diagram CP300 Top screen “CAMERA ID” screen MODEL WV-CP300 SERIES **CAMERA ID** CAMERA ID 0123456789 CAMERA ABCDEFGHIJKLM SYSTEM NOPQRSTUVWXYZ SPECIAL ().,'":;&#!?= LANGUAGE +-*/%$ SPACE POSI RET TOP END RESET ....SETUP DISABLE “CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC SHUTTER... -
Page 9: Camera Title Setting [Camera Id]
Camera title setting [CAMERA ID] This item specified the camera title. The camera title is named with up to 8 characters when using only Chinese characters, and up to 16 characters when using only English letters or num- bers. Chinese character, English letters and numbers can be used together. The "CAMERA ID" display can be turned on or off on the monitor screen. -
Page 10: Camera Operation Setting [Camera Setup]
Camera operation setting [CAMERA SETUP] The following settings related to camera actions can be configured on the "CAMERA SETUP" screen displayed from the top screen. Refer to page 5-6 for how to call up the screen. The settings configured on the "CAMERA SETUP" screen will be saved as a scene file. 1 Register a scene file [SCENE1/SCENE2] It is possible to register 2 patterns of scene file. -
Page 11: Light Quantity Control Method Selection [Alc/Elc]
2 Light quantity control method selection [ALC/ELC] The method of controlling the quantity of light is selected from the following in accordance with the lens to be used. ALC (default): The iris of the lens is automatically adjusted in accordance with the brightness of a subject. -
Page 12: Electronic Shutter Setting [Shutter]
Note: • When “BLC” is set to “ON”, “ABS” displays “---” and may not be operated. Step 4 When "BLC" is set to "OFF", bright areas of an image are masked to facilitate the visibility of dark areas. Move the cursor to "MASK SET" and press the [SET] button. →... -
Page 13: Electronic Sensitivity Enhancement Setting [Sens Up]
Note: • When "SENS UP" is set to the AUTO mode, “AGC” cannot be set to “OFF”. 5 Electronic sensitivity enhancement setting [SENS UP] Use of the electronic sensitivity enhancement function increases the light sensitivity of the CCD, and accordingly the image becomes brighter. The magnification is unchanged for selec- tion of FIX, and the magnification is automatically adjusted in accordance with the illuminance of a photographic subject for selection of AUTO. -
Page 14: Manual Fine Adjustment Of White Balance
Step 1 Set "WHITE BAL" to "AWC" and press the [LEfT ] button to change to "AWC → PUSH SET". Step 2 Press the [SET ] button and adjust the white balance. "AWC → PUSH SET" is reversely high- lighted during adjustment. When the reversely highlighted display is restored, the white balance adjustment is completed. -
Page 15: Digital Noise Reduction Function Setting [Dnr]
Step 4 Move the cursor to "POSITION" and press the [SET ] button. Step 5 Press the [uP], [dOwN], [rIghT] and [lEfT] buttons to move to the upper-left part of the area to be set, and press the [SET ] button. Step 6 Press the [uP], [dOwN], [rIghT] and [lEfT] buttons to move to the lower-right part of the area to be set, and press the [SET ] button. - Page 16 CP310 CP310 AUTO: Similar to the basic functions of AUTO1, but does not change the IR filter. CP300 Switches to black-and-white images when brightness (illuminance) around the camera is lower than approx. 0.1 lx. OFF (default): Displays color images. Note: •...
-
Page 17: Vmd Setting [Vmd]
Note: • Images may not be displayed appropriately without burst signals when camera images are displayed in the black-and-white mode depending on a monitor or VCR model to be used. In such a case, set the burst signal output to "ON". 9 VMD setting [VMD] The VMD function allows the camera to detect object motion and hindrance to the camera. - Page 18 Step 2 Move the cursor to "MASK SET" and press the [SET] button. → The “MASK SET” screen appears. “MOTION DET” screen “MASK SET” screen ** MOTION DET **(1) ..I .. 20 LEVEL DWELL TIME DISPLAY MODE ALARM MASK SET RET TOP END In the masked area, no alarm will be issued even if a moving object is detected.
-
Page 19: Setting Of Scene Change Detection
Step 6 Move the cursor to “Level”. Use the [RIGHT] or [LEFT] button to adjust the level. Repeat step 5 and 6 to adjust to optimal level. Step 7 Move the cursor to “DWELL TIME ”. Select the dwell time from the following. 2 S (default)/5 S /10 S /30 S Alarm signal will be issued once a continuously moving object is detected within the specified time. -
Page 20: Camera System Setting [System Setup]
Camera system setting [SYSTEM SETUP] Performs the settings relating to the camera system such as synchronization and privacy zone. The following settings can be configured on the "SYSTEM SETUP" screen displayed from the top screen. Refer to page 5-6 for how to call up the screen. “SYSTEM SETUP”... -
Page 21: Image Stabilizer Setting [Stabilizer]
→ The "ZONE NUMBER" screen appears. Step 2 Move the cursor to the number at the right of the title and select the zone number using the right or left button. Step 3 Move the cursor to "POSITION" and press the [SET ] button. Step 4 Use the [UP], [dOwN], [RIghT], and [lEfT ] buttons to determine the left upper position of the zone to be set and press the [SET] button. -
Page 22: Upside-Down Setting [Upside-Down]
When "ON" is selected, the zoom factor and the panning/tilting settings can be configured. Follow the procedure below. “SYSTEM SETUP” screen EL-zoom setting screen Zoom setting screen Pan/tilt setting screen ** EL-ZOOM ** ** EL-ZOOM ** ** EL-ZOOM ** **SYSTEM SETUP** SYNC ZOOM ZOOM... -
Page 23: Special Menu Setting [Special Setup]
Special menu setting [SPECIAL SETUP] The special menu setup is performed including the setting of the camera image quality and the communication configuration when a decoder is used. The following settings are to be config- ured on the "SPECIAL SETUP" screen displayed from the top screen. Refer to page 5-6 for how to call up the screen. -
Page 24: Flaw Compensation [Pix Off]
J Flaw compensation [PIX OFF] Flaws of pixel in the displayed camera image are corrected. Up to 16 points can be corrected. Follow the procedure below. Step 1 Move the cursor to "PIX OFF" and press the [SET] button. → The "PIX OFF" screen appears. Step 2 Select a number (1 to 16) with which a pixel compensation point is registered and press the [SET] button. -
Page 25: Default Resetting [Camera Reset]
L Default resetting [CAMERA RESET] The settings in the setup menu are restored to the default settings. Move the cursor to "→ PUSH SET" of "CAMERA RESET" and hold down the [SET] button for more than 2 seconds to enter the next screen. To return to the previous screen without reset- ting, move the cursor to “NO”... -
Page 26: Camera Language Selection [Language Setup]
Camera language selection [LANGUAGE SETUP] The language selection can be made on the "LANGUAGE SETUP" screen displayed from the top screen. Refer to page 5-6 for how to call up the screen. "LANGUAGE SETUP" screen **LANGUAGE SETUP** LANGUAGE ENGLISH RET TOP END Move the cursor to “LANGUAGE”, use the [RIGHT] or [LEFT] button to select the target lan- guage, then move the cursor to “SET”, and press the [SET] button. -
Page 27: Shortcut Operation
Shortcut operation Use of a system controller with the "Camera function" button allows users to perform the shortcut settings with use of the numeric keypad and camera function button. The available shortcut operations with this unit are shown as follows. System controller operation Setting contents CP310... - Page 28 Panasonic System Communications Company of North America, Unit of Panasonic Corporation of North America www.panasonic.com/business/ For customer support, call 1.800.528.6747 Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A. Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 www.panasonic.ca...