Table of Contents
Advertisement
VCR OPERATION
To stop a Timer Programme which has already started
Press STOP/EJECT on the VCR/DVD.
NOTE: STOP on the remote control will not function in the
"Timer Recording" mode.
To correct timer programmes
If you want to correct an automatic timer after you finished
setting programme,
1
Repeat steps
1
to
3
2
Select the setting you want to change using s or B.
3
Enter the correct numbers using K or L, then press B.
4
Press MENU to exit.
5
Press TIMER ON/OFF to return to timer stand-by mode.
To cancel or check the start/end time
1
Repeat steps
1
to
2
2
Select a programme number you want to check using K
or L. The details of selected programme appears on the
TV screen. You may cancel the entire programme by
pressing s.
3
Press MENU button to exit.
To avoid overlap of TIMER programmes ...
A timer programme will not work while another programme is
under execution.
Programme 1
Programme 2
Programme 3
9:00
Hints for Timer Recording
• If there is a power failure or the VCR/DVD is unplugged for
more than 1 hour, clock and all timer settings will be lost.
• If a tape runs out before a timer recording is finished, the
unit ejects the tape and switches into DVD mode automati-
cally. Press TIMER ON/OFF to active VCR function.
• Once the unit goes into Timer-standby mode, no VCR func-
tions are available until TIMER ON/OFF is pressed. (OUT
PUT on the front panel and VCR on the remote control will
not function.)
• Press TIMER ON/OFF to activate VCR functions after your
timer recording is finished.
• DVD functions are available during Timer-standby mode and
Timer recording. You don't have to stop your timer recording.
• If the DVD does not be used after you set the VCR/DVD in
Timer-standby mode by pressing TIMER ON/OFF, press
OPERATE to turn off the VCR/DVD.
in the "Timer Recording" section.
in the "Timer Recording".
10:00
11:00
Index Search
• The index mark will be made automatically when
REC/OTR is pressed. It will also be marked at the starting
point of Timer recording and OTR.
• The index mark is not recorded if STILL/PAUSE is
pressed and released during recording.
• The time gap between index marks on the tape should be
greater than 1 minute for SP recording and 2 minutes for
LP recording.
1
Press VCR, then SEARCH MODE.
2
Press K or L repeatedly until the number of pro-
grammes that you want to skip appears.
3
Press s or B.
The VCR/DVD begins rewinding or fast forwarding to the
beginning of desired programme.
• When the preset programme is reached, the VCR/DVD
will start playback automatically.
NOTES:
• Index Search can be set up to 20.
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds,
2
from steps
mode will be cancelled.
• To exit the Index Search mode, press MENU in step
2
. Or press STOP after step
Time Search
If a tape includes both programmes recorded in the PAL sys-
tem and ones recorded in the NTSC system, this function
may not be operated correctly.
1
Press VCR, then SEARCH MODE twice.
2
Press K or L repeatedly until the desired time appears.
3
Press s or B.
The VCR/DVD begins rewinding or fast forwarding to the
specified point.
When 0:00 is reached, the VCR/DVD will start playback auto-
matically.
NOTES:
• Time Search can be set up to 9 hours 59 minutes
(9:59).
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds,
from steps
2
will be cancelled.
• To exit the Time Search mode, press MENU in step
Or press STOP after step
– 17 –
3
to
. Otherwise the Index Search
3
.
to
3
. Otherwise the Time Search mode
3
.
2
.
EN
Advertisement
Table of Contents
