Download  Print this page

Kenmore 625.381560 UltraFilter 450 Owner's Manual page 15

Reverse osmosis system
Hide thumbs

Advertisement

water supply
fitting
HOT
COLD
/
sink p-trap
NOTE:
Tube colors
match
Caltet
colors
3/8"
black
tubing
NOTE:
Tubing
lengths
should allow
for the removal
of the assembly
from the hanger
washers
for servic-
ing. If tubing
lengths
are shortened
for neater
appearance,
it may be necessary
to keep the assem-
bly on the hanger
washers
for service.
NOTE:
Codes in the state of Massachusetts
require
installation
by a licensed
plumber
and do not permit
the use of saddle
valves.
If you live in the state of
Massachusetts,
review
plumbing
code 248-CMR
of
the Commonwealth
of Massachusetts
before
pro-
ceeding
with the installation.
3/8"
yellow
tubing
tubing
onnector
Tube Connections
Figure 21
CONNECT
YELLOW TUBE TO STORAGE TANK
1. Locate
the yellow
tube.
One end is attached
to the Reverse
Osmosis
filter
assembly.
2. Run the other
end of the yellow
tube to the fitting
on top of
the storage
tank.
See Figure 21.
3. Cut tube
square
and to length.
See Figure 17.
4. Do not connect
at this time. This will occur
in the sanitizing
step.
CONNECT
GREEN
TUBE
TO COLD
WATER
SUPPLY
PIPE
1. Run one end of the 1/4"
green tube to the fitting
on the water
supply
pipe. See Figure 21.
2. Cut tube square
and to length.
See Figure 17.
3. Connect
to cold water
supply
fitting.
See Figure 5.
4. Run the other end of the green tube to green collet to the fit-
ting on the left side of the Reverse Osmosis filter
assembly.
5. Cut tube square
and to length.
See Figure 17.
6. Insert all the way
into the fitting.
See Figures 18A & 18B.
7. Pull on the tube to be sure it is held firmly
in the fitting.
CONNECT
RED TUBE TO REVERSE OSMOSIS
FAUCET
The red tube connection
was completed
in the faucet
assembly
steps.
CONNECT BLUETUBE TO REVERSEOSMOSIS ASSEMBLY
1. Locate the blue tube.
One end is attached
to the faucet.
2. Run the other
end of the 3/8"
blue tube to the blue collet
on
the right
side of the Reverse Osmosis
filter
assembly.
3. Cut tube
square
and to length.
See Figure 17.
4. Insert all the way into the fitting.
See Figures 18A & 18B.
5. Pull on the tube
to be sure it's held firmly
in the fitting.
CONNECT
BLACK
TUBE
FROM
REVERSE
OSMOSIS
FAUCET
TO DRAIN
ADAPTER
1. Locate the 30" length
of 3/8"
black
tube.
One end is
attached
to the faucet.
Figure
21.
2. The other end needs to be attached
to the black
collet
on the
sink drain
adapter.
3. Cut this tube as needed
to route in as straight
of a run as
possible,
without
loops, dips, low spots or kinks.
4. Cut the end of the tube square.
See Figure 17.
5. Insert all the way into the fitting.
See Figures 18A & 18B.
6. Pull on the tube to be sure it is held firmly
in the fitting.
Questions?
Call The Kenmore
Water
Line 1-800-426-9345
or visit KenmoreWater.com
15

Advertisement

loading

  Also See for Kenmore 625.381560 UltraFilter 450

  Related Manuals for Kenmore 625.381560 UltraFilter 450

This manual is also suitable for:

Ultrafilter 450