Download Print this page

Tools Needed - Craftsman 351.215080 Operator's Manual

4 x 8" and 6 x 12" sanding centers
Hide thumbs

Advertisement

_i_htFax
9/10/2003
10:38
PAGE
4/41
RightFax
Refer to Figure 1.
Check for shipping damage,
If damage has occurred, a claim
must be filled with carrier, Check for completeness.
Immediately repeit missing pal"is to dcoter.
The sanding center comes assembled as one unit. Additional
parts which need to be fastened to the sand[rig center should
be located and accounted for before assembling.
A Sanding Center
B Disc Table Assembly
C Disc Table Handle (2)
D Miter Gauge Assembly
E %" Abrasive
Sleeve
F
Belt Table Assembly
G Toolbox with Pan Head Screws
H Dust Chute with Pan Head Screw
I
Belt Table Handle, Sleeve and Locking Nut (21508)
J
Belt Table Handle and Locking Nut (21516)
K Belt Platen Assembly
L
Abrasive Belt
M Drive Roller with Set Screw (21508 only)
N Belt Dust Chute with Pan Head Screws
O Disc Adjustment Wrench (3ram)
P V=" Drum Washer
O %'Table Insert
R Dust Collection Bag with Clamp
Not Shown: 3, 4 and 5ram Hex Wrenches, Belt Table Pointer
with Screw, Disc Table Pointer with Screw and 2 Lifting Hooks
(21516 only).
A
S C
DE
%o
Figure t - Unpacking Bander
@
__\R
WARNING:
Do not operate machine until coreptetely
assembled. Do not operate machine until you have completely
read and understood this manual.
TOOLS
NEEDED
While assembling your sanding center, you will need the
following tools:
• 3, 4,5ram Hex Wrenches
• Combination
Square
• Phillips Screwdriver
MOUNT
SANDING
CENTER
i
Refer to Figures 2 and 3.
NOTE: Although compact, the sanding
centers are heavy, At
least two people are required to riftfrom carton. The 21516 is
supplied with lifting hooks. Thread hooks into the cabinet, lift
machine to desired lecaUon, then remove and store hooks,
Choose a suitable location to mount the sanding center. The
sanding center must be installed in a place with ample lighting
and correct power supply. To install sanding center:
• "The sanding center must be bolted to a firm, level surface.
• Make sure there Is plenty of room for moving the work-
place, There must be enough room that neither operators
nor bystanders will have to stand In line with the wood
white L_sthg the tool. Allow room so that belt assembly can
be positioned horizontally.
• Sanding center can be Installed on a workbench or a tool
stand _sse Recommended Accesoodes, pages t9 and 25)
using bolts, t_:t_ washers end hex nuts (not suppl(ed).
E
E
E
E
O4
L i,
./
9tara
L._149m
m _...J=
--
310mm
Figure 2 - 21508 Base Footprint
I
._,....i
E
E
.::IL-L-e............
.,j . .....
grllm
/
./
................... 360ram .................
Figure 3 - 21516
Base Footprint
ATTACH
DISC TABLE
ASSEMBLY
Refer to Figures 4 and 5, page 4.
• Silde disc table assembly
outo the slides on each side of
disc guard. Thread the two handles through truenlons into
threaded holes on each side of disc guard.
• Be sure the gap between the disc and disc table Is V,," or
tess.
• )f an adjustment
}s necessary, loosen set screw in alu-
minum disc througt_ the opening at top-rear of disc guard.
Posltlen disc V,," or less from edge of table. Secure disc
with set screw.
3

Advertisement

loading

  Related Manuals for Craftsman 351.215080

This manual is also suitable for:

351.215160