Maintenance; Horizontal Belt Sanding; Replacing The Abrasive Disc; Abrasive Disc Finishing - Craftsman 351.226711 Owner's Manual

OPERATING INSTRUCTIONS (Contlnued)
Figure 4
HORrTONTAL BELT SANDING
11_ belt houa_ _n be tired to a ho_zo_l pa_
Removethe belttabfaby mmovlngthe amcka headbolt
and_t wMher (KWNOL62 & S4).
Loo_m the socker hind bdt (Key No. 62); tlt lhe belt
hou_g tothehortzor_poe_n, and_en me eoGk.
e_head bait to =meumthe po_lon.
TI_ drlvo wh_ of the b_t oan be u_l as _lta_
for _cllng _ sudac_
A wodaltop (Key No. 66) Is provlded to be uaad when
stndgr,=ndV_ _ the hodzorsd pm_k_
Attach the workaop to me belt housing with ==¢ket
head be. and wuher (K_/Noe, S2 & S4).
Use a _ornblnstlon square to adjust the workstop at g0"
to _ _ with a 1/16" gap between the belt and
worl_op;
NOTE: For
stabllity,
mount the belt and dbc sander to
the bendl top.
REPLACING THE ABRASIVE DISC
Remove disc tab_
Remove aid 8braslve disc by peellng It from slumlnum
dis(;. Removing 81umlnumdisc trom motor 8hall Is not
necessary.
Clean aluminum dlsc If necee,ga_, Select the proper
abrasive disc 8nd apply to aluminum clls_.
_0o, abrasiveused can be changedtOa dlffarentgrit
ro_acgnothe aJum_num €.8C.
Addltlonslaluminumdlace are avsHable,Use I sep-
arate elumlnumdlsofor _ch gritslze used.
Interal_nge the ilun_num dlscto el_nge _ size.
Refll_e dlse table.
ADJUSTING DISC TABLE ANGLE
dll_ tal_e 18IKllUllllll01o from 45" to gO* for beveled
work.
To adjust the dlso table, Iooeen the two knobe and
adJuu to the dselmd angle.
When dleo table Is IR dulmd m_ie, lock II Into p(JUon
bym_.r_y _e_n_ mekno_
ABRASIVE DISC FINISHING
dlso sandingb well eultadfor finishingsmall
fist eurfacee encl conve0( curvad adges.
Movethewodq:_ _ me ckMn_de (rloht) o fthe
faceofthe abrulve dlso.
elxaslve dls_produces almostno sbnmlve e<:_Ion
atthecen_er.
The abraslve dlsc moves fastest and rernov_ more
martial at the outor edge.
If v_ Is fed withoul addltlonal ou_danca, more
materl_l wlll be removad towarcls the ou_" adge of the
disc.
For accuracy use the rnler gauge,
USING THE Mrl'ER GAUGE
(SeeRecommended Accessod_ page11.)
The miter gauga Is used oNy on the disc tabSe,Use the
mlter gauge for secudng work and haidlng the proper
anglewhlledlsc _andln_
Adjust the .angle by _g the relier gauge scale
and locking It Into place with thuml_¢rew and fiat-
washer.
Check the accuracy o_ the miter gauge scale.
Use ii comblnatlorl square to adjust the miter gauge
square to the face o( the dlsc.
Indlcator should be at zero. Loosen screw and reposl-
lion Indlcator If necessary.
MAINTENANCE
WARNING: MAKE CERTAIN THAT UNIT IS DIS-
CONNECTED FROM POWER SOURCE
BEFORE AI"rEMPTING TO SERVICE
OR REMOVE ANY COMPONENT.
CLEANING
Keep machine and workshop dean. Do nol aflow sew-
dust to accumu_te on belt and dtsc undm'.
Keep the wheels dean. Dirt on wheels will ceuse poor
tracking and belt sllppage.
IMPORTANT: AFTER SANDING WOOD OR NON-
METALLIC MATERIAL. ALWAYS CLEAN THE AREA OF
SAWDUST BEFORE GRINDING METAL THE SPARKS
COULD IGNITE THE DEBRIS AND CAUSE A FIRE.
-8-