Operation; Electrical Connections; Mounting Sander To Stand; Specifications - Craftsman 351.225950 Operator's Manual

Extension Cord Length
Wire Size .................................. A.W.G.
Up to 25 ft..................................... 18
NOTE: Using extension cords over 25 ft. long is not
recommended.
MOTOR
The sander/grinder is assembled with motor and wiring
installed as an integral part of the tool. The electrical wiring
schematic is shown in Figure 5.
The 120 Volt AC permanently split capacitor motor has the fol-
lowing specifications:
Horsepower (Maximum Developed) ................. 11/2
Voltage ...................................... 120
Amperes ..................................... 8.0
Hertz ........................................ 60
Phase ..................................... Single
RPM ....................................... 3450
Rotation (viewed from left side) ............... Clockwise
ELECTRICAL CONNECTIONS
WARNING: Make sure unit is off and disconnected from
power source before inspecting any wiring.
The motor is installed and wiring connected as illustrated in
the wiring schematic (see Figure 5).
Switch_i_ Black
-o.....\ To Power
Relay -_ "Green \,._____/_"_
FTo Motor _ S
_ Capacitor I
Figure 5 - Wiring Schematic
The motor is assembled with an approved three conductor
cord to be used on 120 volts as indicated. The power supply
to the motor is controlled by a single pole locking rocker
switch.
The power lines are inserted directly onto the switch. The
green ground line must remain securely fastened to the frame
to properly protect against electrical shock.
• Remove the key to prevent unauthorized use.
MOUNTING SANDER TO STAND
Refer to Figures 6 and 8, pages 5 and 9.
Install sander on the stand.
Align mounting holes on sander with slots on top frame
(Fig. 8, Key No. 1).
Secure sander to stand on all four corners using hex head
bolts and hex nuts (Fig. 8, Key Nos. 8 and 9).
Figure 6 - Mounting Sander to Stand
Refer to Figures 7 and 9, pages 6 and 10.
DESCRIPTION
Craftsman 6" Belt and 9" Disc Sander is constructed of
rugged die cast aluminum and cast iron providing stability and
vibration-free operation. The 6 x 48" belt and 9" diameter disc
are used to sand, deburr, bevel and grind large workpieces of
wood, plastic and metal.
The 6 x 48" belt housing can be pivoted from vertical to hori-
zontal for sanding large, straight workpieces. The belt assem-
bly includes a tilting, cast iron table with miter gauge and dust
collection chute.
The 9" diameter disc can be used to sand or bevel surfaces
with the use of 0 to 45 ° scaled aluminum table. The 9" diam-
eter disc assembly includes a tilting table with miter gauge
slot and dust collection chute.
The 3" diameter idler drum permits the sanding of contoured
shapes and finishes by positioning the adjustable platen from
a horizontal to vertical position.
The two collection chutes with adaptable exhaust ports allow
for quick removal of dust. The adjustable miter gauge can be
used on both the belt and disc tables for guiding the work-
piece at a desired angle while sanding.
SPECIFICATIONS
Belt size ............................. 6 x 48", 80 grit
Belt platen area .......................... 71/8x 167/8 ''
Belt table dimensions ....................... 57/8x 97/8 ''
Belt table tilts .............................. 0 to 60 °
Belt dust chute diameter ......................... 21/2 ''
Belt speed .............................. 2700 FPM
Disc diameter ............................ 9", 80 grit
Disc table dimensions ...................... 57/8x 117/8 ''
Disc table tilts .............................. 0 to 45 °
Disc dust chute diameter ........................ 13/4"
Disc speed .............................. 3450 RPM
Base dimensions ........................ 131/2x 138/8 ''
Switch ................... 120 Volts, SP, Locking rocker
Motor ...... 11/2HP(max. developed) 3450 RPM, 8.0 AMPS
Weight .................................... 105 Ibs
5