Sony XM-1002HX Operating Instructions page 3

Connections
Caution
• Before making any connections, discolu_ect
the ground terminal of the car battery to avoid
short circuits.
* Be sure to use speakers with an adequate
power rating. If you use small capacity
speakers, they may be damaged.
• Do not connect the 0 terminal of the speaker
system to the car chassis, and do not connect
the 0 terminal of the right speaker with that
of the left speaker.
• Install the input and output cords away from
the power supply lead as running them close
together can generate some interference noise.
I This unit is a high powered amplifer.
Therefore, it may not perform to its full
potential if used with the speaker cords
supplied with the car.
• If your car is equipped with a computer
system for navigation or some other purpose,
do not to remove the ground wire from the
car battery. If you disconnect the wire, the
computer memory may be erased. To avoid
short circuits when making connections,
disconnect the +12 V power supply lead until
all the other leads have been connected.
Make the terminal
connections as Illustrated below.
Note
When you tighten the screw, be careful not to
apply too much torque* as doing so may damage
the screw.
* The torque value should be less than 1 N•m.
Pass the leads
through the cap,
connect the leads,
then cover the
terminals with the
cap.
.)
Power Connection Leads
C&bles d'alimentation
(
Remote output * |
Sortie de
I
tdldcommande *
(REM OUT)
1_ IIII1_ to a metal point of the car
vers une pattie mC_tallique
de la carrosserie
O O
Car audio [ _
Fuse (30 A)
Autoradio Fusible (30 A)
+12 V car battery
Batterle de volture +12 V
* If you have the factory original or some other car audio without a remote output on the amplifier, connect the remote input
terminal (REMOTE) to the accessory power supply.
* Si vous disposez du moddle d'origine ou d'un autre autoradio dont l'amplificateur ne comporte pas de sortie de
t_qdcommande, raccordez la borne d'entr_e de tdl_commande (REMOTE) _la prise d'alimentation aecessoires.
Notes on the power supply
• Connect the +12 V power supply lead only after all the
other leads have been connected.
• Be sure to connect the ground lead of the unit
securely to a metal polnt of the car. A loose
connection may cause a malfunction of the
amplifier.
• Be sure to connect the remote control lead of the car audio
to the remote terminal.
• When using a car audio without a remote output on the
amplifier, connect the remote input terminal (REMOTE)
to the accessory power supply.
• Use the power supply lead with a fuse attached (30 A).
• Place the fuse in the power supply lead as close as possible
to the car battery.
• Make sure that the leads to be connected to the +12 Vand
GND terminals of this unit respectively must be larger
than l O-Gauge (A WG- I O) or "with the sectional area of
mare than 5 mmL
• When using the optional RC-46 power amplifier
connecting cord, consult that manual for proper use.
2-Speaker System
Syst_me & 2 haut-parleurs
I
Car audio I
Autoradio
Left speaker Right speaker
(min. 1_/2Q)* _ _ (min. 1_/2L'1)*
Haut-parleur Haut-parleur
gauche d roit
(rain. 1_/2Q)* l* HI-CURRENT/HI-VOLTAGE
mode I
(mln. 1_/2Q)* * mode HI-CURRENT/HI-VOLTAGE
For details on the settings of switches and controls,
refer to "Location and Function of Controls."
Pour plus de ddtails sur les rdglages des commutateurs et
eommandes, reportez-vous _ "Emplacement et _nction
des commandes".
As a Monaural Amplifier
Comme amplificateur monaural
i Car audio I
Autoradio
LINE OUT
Left channel _ Right channel
Canal gauche _ Canal droit
Left speaker ?
(min. 2_/4_Q)* _
Haut-parleur
gauche
(mln. 20/4_)* I* HI-CURRENT/HI-VOLTAGE mode ! Right speaker (mln. 2_/4_)*
I
• mode HI-CURRENT/H!-VOLTAGE ] Haut-parleur droit (min. 2_/4_)*
For details on the settings of switches and controls,
refer to "Location and Function of Controis."
Note
Make sure that the line output from the car audio is
connected to the jack marked "L (MONO)" on the
unit.
Pour plus de ddtails sur les rdglages des commutateurs
et commandes, reportez.vous _ "Emplacement et
fenction des commande: ".
Remarque
V_rifiez que la sortie de ligne de l'autoradio est
raccordde _la prise portant l'indicatlon "L (MONO)"
sur l"appareil.
As the Monaural Amplifier for a Subwoofer
Comme amplificateur monaural pour un haut-parleur
d'extr_mes graves
I
Car audio
Autoradio
LINE OUT
Subwoofer (rain. 2_/4_)*
Subwoofer (mln. 2_/4_)*
For details on the settings of switches and controls,
refer to "Location and Function of Controls."
Note
If you wish to use a subwoofer as a monaural speaker,
connect the speaker as illustrated above. The output
signals to the subwoofer will be the combination of the
both right and left output signals.
* HI-CURRENT/HI-VOLTAGE mode
• mode HI-CURRENT/HI-VOLTAGE
Pour plus de ddtails sur les rdglages des commutateurs
et commandes, reportez-vous _ "Emplacement et
fonction des commandes".
Remarque
Si vous d_sirez utiliser un haut-parleur d"extr_mes
graves comme haut-parleur monaural, raccordez ls
haut-parleur comme illustrd ci-dessus. Les signaux de
sortie vers le haut-parleur d' extr_mes graves seront une
combinaison des signaux de sortie droit et gauche.
2-way System
Syst_me 2 voies
Two output channels
Duex canaux de sortie
Full range
speakers
(mln. 1_2/2Q)*
Haut-parleurs h
large bande
(rain. 1_/2_)*
Car audio I Autoradio
E OUT
d h
• IIII _-_
O@€_O OOOO
* HI-CURRENT/HI-VOLTAGE mode 1 • mode HI-CURRENT/HI-VOLTAGE
Use the THROUGH OUT terminal when
you install more amplifiers. The signals are
output as they were input. (LOW BOOST,
HPF, LPF do not work.)
Notes
• A maximum 3 amplifiers can be connected to the
THROUGH OUT terminal. If you connect more
than three ampli_ers, it may cause problems such as
sound dropout.
• High level input connection cannot use THROUGH
OUT.
Utilisez la borne THROUGH OUT lorsque
vous installez plusieurs amplificateurs. Les
signaux sont sortis comme ils sont entr4s.
(LOW BOOST, HPF, LPF ne fonctionnent
pas.)
Remarques
• Vous pouvez raccorder un maximum de3
ampliJicateurs _la borne THROUGH OUT. Si vous
raccordez plus de trois amplificateurs, cela peut
provoquer des probl_mes comme des baisses du son.
• Avec une connexion d'entrde de haul niveau, vous ne
pouvez pas utiliser THROUGH OUT.
Four output channels
Quatre canaux de sortie
Ca r audio
Autoradio
Full range
speakers
(mln. 1_/2_z) •
Haut-parleurs
/i large bande
(min. 1_/2_) •
_/_ _E OUT
0€O0 OO00
Subwoofers
(mln. 1G_/2_)* [_
For details on the settings of switches and controls,
refer to "Location and Function of Controls."
Note
In this system, the volume of the subwoofers will be
controlled by the car audio fader control.
* HI-CURRENT/HI-VOLTAGE mode
I
* mode HI-CURRENT/HI-VOLTAGE ]
Pour plus de d_tails sur ies r_glages des commutateurs
et commandes, reporte'z-vous _ "Emplacement et
fonction des commandes'.
Remarque
Dans ce syst_me, le volume des haut-parleurs
d" extr_nes graves est contralti par la commande de
balance avant/arridre de l'autoradio.
Dual Mode System (With a Bridged Subwoofer)
Double mode de connexion (avec un haut-parleur
d'extr_mes graves en pont)
Car audio T_
Autoradlo
L LINE OU
C2
Left speaker Right speaker
Haut-parleur gauche Haut-parleur drolt
Table of crossover values for
6 dB/0ctave (4 ohms)
Subwoofer
Subwoofer
Tableau des valeurs de recoupement
pour 6 dB/octave (4 ohms)
Crossover L C 1 / C2 Fr6quence de L C1 / C2
Frequency (coil)* (capacitor)* recoupement (bobine)* (condensa-
unit: Hz unit: mH unit: _F unit_: Hz unit_:mH teur)* unit4:/_F
50 12.7 800 50 12,7 800
80 8.2 500 80 8,2 500
100 6.2 400 100 6,2 400
130 4.7 300 130 4,7 300
150 4.2 270 150 4,2 270
200 3.3 200 200 3,3 200
260 2.4 150 260 2,4 150
400 1.6 100 400 1,6 100
600 1.0 68 600 1,0 68
800 0.8 50 800 0,8 50
1000 0.6 39 1000 0,6 39
* (not supplied) * (non fournis)
Notes
• When using passive crossover networks in a multi-speaker
system, care must be taken as the speaker system's
;impedance should not be lower than that of the suitable
;impedancefor this unit.
• When you are installing a 12 decibels/octave system in
your car, the following points must be considered. In a 12
decibels/octave system where both a choke and capacitor
are used in series to form a circuit, a great care must be
taken when they are connected. In such a circuit, there is
going to be an increase in the current which by-passes the
speaker with frequencies at around the crossover
frequency. If audio signals are continued to befed into the
crossover frequency area, it may cause the amplifier to
become abnormally hot or the fuse will be blown. Also if
the speaker is disconnected, a series-resonant circuit will
be formed by the choke and the capacitor. In this case, the
impedance in the resonance area will decrease
dramatically resulting in a short circuit like situation
causing a damage to the ampli_er. Therefore, make sure
that a speaker is connected to such a circuit at all times.
High Level Input Connection
(As a Monaural Amplifier for a Subwoofer)
Connexion d'entr_e il haut niveau
(Comme ampllficateur monaural pour un haut-parleur d'extr_mes
graves)
Left speaker
Haut-parleur gauche
Right speaker
Haut-parleur drolt
Car audio I
Autoradio
Input cord (Not supplied)
Cable d'entMe (Non fournls)
I I
O
Subwoofer (min. 2_/4_)* • mode HI-CURRENT/HI-VOLTAGE
For details on the settings of switches and controls,
refer to "Location and Function of Controls."
Note
If you wish to use a subwoofer as a monaural speaker,
connect the speaker as illustrated above. The output
signals to the subwoofer will be the combination of both
the right and left output signals.
High Level Input Connection (2-SpeakerSystem)
Connexion d'entr_e & haut niveau
(Syst_me tt 2 haut-parleurs)
Input cord (Not supplied)
C&ble d'entr_e (Non
foumls)
White O Left speaker output
Blanc _ mbm_O_D "_rtle[ I haut-parleur gauche
""1 Car audio
Black-striped cord O /_ Autoradlo
Cordon ra_ _!__Rlght I
Gray mb speaker output
Grls Sortie haut-padeur drolt
Black-striped cord
Cordon ray_ now
I
IIII
O@€O
Left speaker _ _ Right speaker
(mln. 1_/2Q)* _ _ (mln. 1_/2_'1) •
Haut-parleur Haut-parleur
gauche I HI-CURRENT/HI-VOLTAGE mode _I droit
(mln. 1_/2_)* : mode HI-CURRENT/HI-VOLTAGE I (mln. 1_/2_)*
For details on the settings of switches and controls,
refer to "Location and Function of Controls. "
Pour plus de ddtails sur les r_glages des commutateurs
et commandes, reportez-vous _ "Emplacement et
fenction des commandes".
i
High Level Input Connection (Asa
Monaural Amplifier)
Connexion d'entrde & haut niveau
(Comme amplificateur monaural)
Black-stripedcord Left speaker output Right speaker output
Cordon ray_ nolr Sortie haut-parleur gauche Sortie haut-parleur
drolt
Caraudio
Autoradio
Input cord (Not supplied)
Clible d'entr6e (Non fou rnls)
Black-striped cord
Cordon ray_ nolr
0 € 0 •
Left speaker y Right speaker U
Haut-parleur Haut-parleur drolt
gauche (min. 2Q/4Q)*
(rain. 2_/4_)*
I* HI-CURRENT/HI-VOLTAGE mode
I
• mode HI-CURRENT/HI-VOLTAGE
I
I
For details on the settings of switches and controls,
refer to "Location and Function of Controls."
Note
Make sure that the line output from the car audio is
connected to the jack marked "L (MONO)" on the
unit.
Pour plus de dgtails sur les rdglages des commutateurs
et commandes, reportez-vou_ _ "Emplacement et
fonction des commandes'.
Remarque
V_ri_ez que la sortie de ligne de l'autoradio est raccordde
la prise portant l'indicatlon "L (MONO)" sur
l'appareil.
Speaker cord direct in connector
Cordon de haut-parleur directement dens le connecteur
.1
*2
White F
Blan_
Left speaker
Haut-padeur gauche I Car audio
Right speaker Ii Autoradlo
Haut-padeur droit
G_.ray Black-stripedcord
Gds Cordon ray_ nolr
f
"1
Left speaker
Haut-parleur gauche I
Car audio
Autoradlo
Right speaker
I Haut-parleur drolt
Black/Gray
Nolr/Gris ___
Gray
Gds
_,_ Cord diameter 0.3 - 1.25 mm (AWG 22 - 16)
J _ Section du cordon : 0,3 - 1,25 mm (AWG 22-16)
Flat-head screwdriver
Tournevls ,_ lame plate _.___.__ 11 (_hi)
Unit : mm (in.)
Unit_ : mm (po.)
i
i