Gas Conversion Kits - Superior SDV35-N Installation Instructions Manual

GAS CONVERSION KITS

This conversion kit shall be installed by a qualified service agency in accor-
dance with the manufacturer's instructions and all applicable codes and
requirements of the authority having jurisdiction. If the information in these
instruction is not followed exactly, a fire, explosion or production of carbon
monoxide may result causing property damage, personal injury or loss of
life. The qualified service agency is responsible for the proper installation
of this kit. The installation is not proper and complete until the operation
of the converted appliance is checked as specified in the manufacturer's
instructions supplied with the kit.The qualified service agency performing
this installation assumes responsibility for this conversion.
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l'autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d'incendie, d'explosion ou la production de monoxyde de carbone pouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agréé est responsable de l'installation de cette trousse. L'installation n'est
pas adéquate ni complète tant que le bon fonctionnement de l'appareil
converti n'a pas été vérifié selon les instructions du fabricant fournies avec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
In Canada:
THE CONVERSION SHALL BE CAR-
RIED OUT IN ACCORDANCE WITH THE
REQUIREMENTS OF THE PROVINCIAL
AUTHORITIES HAVING JURISDICTION
AND IN ACCORDANCE WITH THE RE-
QUIREMENTS OF THE CAN/CSA-B149.1
INSTALLATION CODE.
LA CONVERSION DEVRA êTRE EFFECTUéE
CONFORMéMENT AUX RECOMMANDA-
TIONS DES AUTORITéS PROVINCIALES
AYANT JURIDICTION ET CONFORMé-
MENT AUX EXIGENCES DU CODE
D'INSTALLATION CAN/CSA-B149.1.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete
the task including labeling that must be af-
fixed to ensure safe operation.
Kit part numbers are listed here and the
following steps detail the conversion pro-
cedure. Refer to the instructions provided
with the conversion kit when performing any
gas conversion.
36
WARNING
AVERTISSEMENT
Millivolt SIT Systems
Natural Gas To Propane Gas
Conversion Kits
Model
SDV35
Millivolt SIT Systems
Propane to Natural Gas
Conversion Kits
Model
SDV35
Millivolt HONEYWELL Systems
Natural Gas To Propane Gas
Conversion Kits
Model
SDV35
Millivolt HONEYWELL Systems
Propane Gas To Natural Gas
Conversion Kits
Model
SDV35
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
INSTALLATION INSTRUCTIONS
Step 1. TURN OFF THE GAS SUPPLY TO THE
APPLIANCE and disconnect power supply at the
circuit breaker. Ensure appliance is cold.
CAUTION: THE GAS SUPPLY SHALL BE
SHUT OFF PRIOR TO DISCONNECTING THE
ELECTRICAL POWER, BEFORE PROCEED-
ING WITH THE CONVERSION.
ATTENTION : AVANT D'EFFECTUER
LA CONVERSION, COUPEZ D'ABORD
L'ALIMENTATION EN GAZ, ENSUITE,
COUPEZ L'ALIMENTATION éLECTRIQUE.
Step 2. Remove the front glass door assembly
from the appliance (see Removing Glass Enclo-
sure Panels on Page 30). Remove the control
compartment door (see Control Compartment
Door Removal on Page 26).
Step 3. Carefully remove the logs. Exercise care
so as not to break the logs.
Step 4. Locate the screws securing the burner
assembly to the appliance. Remove the burner
assembly and retain the securing screws.
Step 5. - SIT Systems - Refer to Figure 59 and
the instructions provided with the kit. Using a
Torx T20 (with 1/4" shank and center hole), tool
or standard flat screwdriver remove and discard
the three pressure regulator mounting screws.
Remove the pressure regulator, spring, poppet,
diaphragm and bushing. Discard all removed
components.
Ensure the rubber gasket installed on the back of
the replacement pressure regulator is properly
Cat. No.
positioned and install the new pressure regula-
85L59
tor using the new screws supplied with the kit.
Tighten screws to 25 In. lb. torque.
SIT Millivolt Gas Valve
Cat. No.
Pressure
85L66
Regulator
Cat. No.
11M37
Figure 59
Cat. No.
11M34
Remove
These
Components