Samsung PN50C590 Quick Setup Manual page 2

Step 6
: Remote Control
Remote Control Buttons and Functions
✎
This is a special remote control for the visually impaired and has Braille points on the Power, Channel, Volume, Stop, and Play/Pause buttons.
Turns the TV on and off.
Displays and selects the available video sources.
Have direct access to channels.
Press to select additional channels (digital) being
broadcasted by the same station. For example, to select
channel "54-3", press "54", then press "-" and "3".
Adjusts the volume.
Opens the OSD.
Views Media Play (USB).
Quickly select frequently used functions.
Returns to the previous menu.
These buttons are for the Channel list, Media Play
(USB) menu, etc.
Use these buttons in Media Play (USB) and Anynet+
(HDMI-CEC) modes. (�: Controls recording on
Samsung recorders that have the Anynet+ feature)
POWER
POWER
Changing Channels and Adjusting the Volume
Adjust the volume by pressing the Volume button
on the remote.
MEDIA.P
✎
You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button.
TOOLS
Viewing the On Screen Menus
RETURN
To view the On Screen Menus, follow these steps:
MEDIA.P
1. Turn on your TV, press the MENU button on your A
remote. The main menu appears. TOOLS
S.MODE
The menu's left side has the following menu
P.MODE
options: Picture, Sound, Channel, Setup, Input, Application, and Support.
RETURN
2. Press the ▲ or ▼ button on your remote to select a menu option, and then
press the ENTERE button.
A
3. When done using the menu, press the EXIT button on your remote to exit.
S.MODE
P.MODE
Selecting a Source
To watch a movie on your Blu-ray player or watch
your favorite TV show, you must select the correct POWER
source. A source is a device, such as a Blu-ray/DVD
player, a cable/satellite box, antenna or a cable TV
input. Sources can be connected to your TV through
the HDMI, DVI, Component, Composite, or D-sub
connections, or through the Antenna or Cable In connections.
To view the signal from a source connected to the HDMI, DVI, Component,
Composite, or D-sub jack, press the SOURCE button on your remote. Each time
you press the SOURCE button, you change to a different source.
MEDIA.P
POWER ON/OFF
Turns the remote control light on or off. When on, the
SOURCE buttons become illuminated for a moment when pressed.
(Using the remote control with this button set to off will
reduce the battery usage time.)
✎
Only PC550, PC590 models
Returns to the previous channel.
PRE-CH
Cuts off the sound temporarily.
Changes channels.
CH LIST
Displays channel list on thescreen.
MENU
MEDIA.P FAV.CH
Displays Favorite Channel Lists on the screen.
TOOLS INFO
Displays information on the TV screen.
Selects the on-screen menu items and changes the values
seen on the menu.
RETURN EXIT
Exits the menu.
A B C D
S.MODE: Press to select the sound mode.
S.MODE SLEEP MTS
SLEEP: Use to set the sleep timer function.
P.MODE P.SIZE
CC
MTS: Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
P.MODE: Press to select the picture mode.
P.SIZE: Selects the picture size.
ON/OFF
CC: Controls the caption decoder.
SOURCE
ON/OFF
SOURCE
PRE-CH
Change the channels by pressing the Channel button on the remote.
✎
If your TV is attached to a cable or satellite box, change the channel using
CH LIST
the box's remote.
MENU
FAV.CH
PRE-CH
INFO
Connecting a USB Device for Media Play
CH LIST
EXIT
You can enjoy photo,
MENU MediaPlay
FAV.CH
music, and movie files
B C D
INFO stored on a USB device
Videos
SLEEP MTS
by connecting it to the TV
P.SIZE CC and using the Media Play
feature. To connect a USB
EXIT
device for Media Play,
B C D
follow these steps:
1. Turn on your TV.
SLEEP MTS SUM Change Device
2. Connect a USB device
P.SIZE CC
containing photo, music and/or movie files to the
on the side of the TV.
3. When USB is connected to the TV, popup window appears. Then you can
ON/OFF
select Media Play.
SOURCE
PRE-CH
CH LIST
MENU
FAV.CH
Step 7
: Media Play Features
The Media Play feature lets you connect to your PC through your home network and
stream PC audio and video files to your HDTV using your remote. To use IPTV or
Samsung PC Share Manager, you must connect your TV to your network. You can
attach the TV to your network in two ways, by cable, using CAT 5 cable, or wirelessly,
using a Samsung Wireless LAN Adapter. Instructions for both connection methods are
below.
Network Connection - Wired
There are two main ways to connect your TV to your network using cable,
depending on your network setup. They are illustrated below:
The Modem Port on the Wall
(ADSL / VDSL / Cable TV)
Modem Cable (Not Supplied)
The LAN Port on the Wall
LAN Cable (Not Supplied)
Configuring the Network Connection - Wired
Most home networks use the Dynamic Host Configuration Protocol (DHCP) to
configure network connections. Home networks that support DHCP automatically
provide the IP address, subnet mask, gateway, and DNS values your TV needs to
access the Internet so you don't have to enter them manually.
To configure your network connection for a network that uses DHCP, follow these
steps:
1. Connect your TV to your
network as shown in one of the
illustrations above.
2. Turn on your TV, press the MENU
button on your remote, and then
select Setup → Network.
3. Set the Network Type to Wired if
it is not already set to Wired.
4. Select Network Setup. The
Wired Network Setup screen
appears.
5. On the Wired Network Setup menu, set Internet Protocol Setup and DNS
Setup to Auto Setup. Auto Setup acquires and enters the necessary internet
values automatically.
6. Select Network Test to check Internet connectivity.
✎
Some networks are Static IP networks. If your network is a Static IP network,
you can not use DHCP to configure the network connection. Instead, you
must enter the IP Address, Subnet Mask, Gateway, and DNS Server
manually. For instructions explaining how to configure a Static IP network,
see your user's manual.
View Devices E Enter R Return
USB 1 or USB 2 (HDD) jack
Network Connection - Wireless
You can connect your TV to your LAN through a standard wireless router or
modem. To connect wirelessly, you must first attach a "Samsung Wireless LAN
Adapter" (WIS09ABGN - sold separately) to either the
on the back of your TV. See the illustration below.
The LAN Port on the Wall
LAN Cable (Not Supplied)
TV Rear Panel
External Modem
Samsung's Wireless LAN adapter supports the IEEE 802.11A, IEEE 802.11B, IEEE
802.11G, and IEEE 802.11N wireless communication protocols. For your TV to
LAN Cable (Not Supplied)
connect to your network, the wireless router or modem you use must also support
one of these protocols. The fastest of these protocols is IEEE 802.11N.
Most wireless network systems incorporate a security system that requires devices
TV Rear Panel
that access the network through an access point or AP (typically a wireless modem
or router) to transmit an encrypted security code called an access key.
For regular connections, your TV is compatible with the following security protocols:
y Authentication Mode: OPEN, SHARED, WPAPSK, WPA2PSK
y Encryption Type: WEP, TKIP, AES
Configuring the Network Connection - Wireless
The instructions below are for networks that use the Dynamic Host Configuration
Protocol (DHCP) to configure network connections automatically. If your have a
Static IP network, see your user's manual for configuration instructions.
To configure your network connection for a network that uses DHCP, follow these
steps:
1. Connect your TV to your network
Wired Network Setup
as shown in the illustrations
above.
Internet Protocol Setup : Auto Setup r
IP Address :
2. Turn on your TV, press the
Subnet Mask :
button on your remote, and the
Gateway :
select Setup → Network.
3. Set the Network Type to
DNS Setup : Auto Setup
Wireless if it is not already set to
DNS Server :
Wireless.
U Move E Enter R Return
4. Select Network Setup. The
Wireless Network Setup screen appears.
5. On the Wireless Network Setup menu, select an AP(Access Point) and ad
hoc network. if you have selected network with a security key, the Security
Key screen appears.
6. Enter the security key using the numbers on the remote, and then press the
Blue button on your remote.
✎
If your network uses WEP security encryption, 0~9 and A~F will be
available on the Security Key screen. Use the Direction button on your
remote to move to the characters and the enter key to select them.
7. On the Wireless Network Setup menu, set Internet Protocol Setup
and DNS Setup to Auto Setup. The Auto Setup acquires and enters the
necessary internet values automatically.
8. Select Network Test to check internet connectivity.
✎
For more information, see your user's manual.
USB 1 or USB 2 (HDD) port
TV Side Panel
Samsung Wireless LAN
Adapter
Wireless IP
sharer
or
TV Rear Panel
Wireless Network Setup
Select a network : Not Selected r
Internet Protocol Setup : Auto Setup
MENU
IP Address :
Subnet Mask :
Gateway :
DNS Setup : Auto Setup
DNS Server :
U Move E Enter R Return
BN68-02614A-00