Sears 706.650770 Owner's Manual

f f
SEARS
CRRFTSMRN°
Tool Storage Chest
PROFESSIONAL SERIES
1-Drawer 706.654001
2-Drawer 706.65321 653311 653331
3-D_wer 706.653251 653301 653371
653380 653921 653941
653951 654081 657620
657721 658040 657660
4-Drawer 706.652240 652260 652520
655850 654070
8-Drawer 706.650750 657560 657570
7-Drawer 706.652270 657510 657751
B-Drawer 706.650770 652280 656971
656981 657550 657580
658660
_-Drawer 706.651691 652370
lO-Drawer 706.657380 657590 657740
12-Drawer 706.657390 657521 657540
657610 657791
14-Drawer 706.657350
3AUTION: Read and follow all Safety Rules
_ndOperatingInstructions before first use of
his product.
_ears, Roebuckand Co.
-IoffmanEstates, IL 60179 U.S.A.
Spring
Made in the U.S.A.
F888A1
)IVIDER INSTALLATION:
Dependant on Model No.)
Hold springclipto the side of drawer.
Place the dividerend intospring clip.
Swingthe dividerintoposition,the
springclipwill hold it in place.
The dividermay be cut to fit from the
front to the backof the drawer.
J
SAFETY RULES AND WARNINGS:
• DO NOT stand on this product. You may fall which may cause personal injury.
• WEAR SAFETY GLASSES AND GLOVES when cuttingthe bandingmaterial.The
bands may snap which may cause personalinjury.
• Stacked productsshouldbe boltedtogether.The productscould become unstable and
tip, which may cause personalinjuryor productdamage.
• WEAR SAFETY GLASSES when removingor repositioning the slides. The tool could
slipwhich may cause personalinjury.
• When the cover is opened, be sure the cover stop is in the lockedposition.This will
prevent accidentalclosure and personalinjury.
• BE CAREFUL when closingthe cover. Remove hands before the cover closes
completelyto prevent personalinjury.
• BE CAREFUL when openingmore than one drawer. The productmay become unstable
and tip, whichmay cause personalinjuryor productdamage.
• DO NOT mountthis producton a truck bed or any other movingobject. This may cause
personalinjuryor productdamage.
• DO NOT step in the drawers.You may fall which may cause personalinjury.
• Appropriately secure this productbeforemoving it with a forklift.
• Close the cover and lockthe drawersand doors before movingthis product.The
drawers or doors couldcome open and make the productunstableand tip,which may
cause personalinjuryor productdamage.
• DO NOT alter this productin any manner. For example, do notweld external Iockbarsor
attach electri#_.a| equipment.This may cause productdamage or personalinjury.
• Remove the work surface,if provided,from the cart before mountingthe chest. Failure
to do so may cause the chest to slide off, which may cause personalinjuryor product
damage.
° WEAR SAFETY GLASSES AND BE CAREFUL when movingthe cover rods. The rod
could springout of the hole, whichmay cause personalinjury.
• When lockingthis product,close the drawers before closingthe cover for Iockbarsto
work properly.
• Spread the weight out evenly in the tote trays. If the weightis not spreadevenly, the
contentscould shift and fall out,which may cause personal injury,and/or damage to the
contentsor tote tray.
• The maximumweight for each drawershouldbe no more than 50 pounds.
Call 1-800-366-7278 for Service Parts
Refer to Service Parts Drawing for full listing of Service Parts
DRAWER REMOVAL:
= Fully extend the drawer. Push it back a quarter of
an inch.
• Insert a screwdriver into the slot in the slide and push
in on the stop until it clears the lance. Repeat the
procedure on the other slide and remove the drawer.
Slot _ Stop
__bricate __
° To reinstall the drawer, pry the stop far enough out to engage the lance and push the
draweronto the slidesuntilthe stopspass over the lances.
LUBRICATIO.N. Lubricate the top and bottom channels of the drawer slides at least
twice a year.
REPOSITIONING THE COVER RODS: The cover rod can be repositioned for
customized storage needs.
• Hold the rod firmly at both ends. Slide the rod to one end and flex the center portion of
the rod until its end is free of the hole.
• Insert the rod into an alternate hole location and reverse this procedure. WEAR
SAFETY GLASSES and use extreme caution during this procedure.
J