Advertisement
Quick Links
®
Save This
Manual
For Future
Reference
OW
°
MANUAL
Model No.
319.226560
Serial No.
Model and serial
numbers may be
found on the nam
plate located on the
front of the tool. You
should record both
the model and serial
number and retain it
in a safe place for
future use.
Caution:
Read, understand
and
follow ALL Instruc-
tions
and rules
for
safe operation
before
operating
this
tool.
LT/
SANDER
C
• Warranty
. Safety Instructions
" KnowYour
Belt/Disc Sander
• Operation
and Maintenance
• Repair Parts
226560102
226560102
Sears,
Roebuck
and Co.,
Hoffman
Estates,
lL 60179
U.S.A.
NRTL/C
LR 78936
Advertisement
Related Manuals for Sears Craftsman 319.226560
Summary of Contents for Sears Craftsman 319.226560
- Page 1 ® Save This Manual For Future Reference ° MANUAL Model No. 319.226560 Serial No. Model and serial numbers may be found on the nam plate located on the front of the tool. You SANDER should record both the model and serial number and retain it in a safe place for future use.
- Page 2 WARRANTY SEARS BELT and DISC SANDER If this Sears Craftsman Belt and Disc Sander fails due to a defect in material or workmanship within one year' from the date of purchase, RETURN IT TO THE NEAREST SEARS SERVICE CENTER INTHE UNITED STATES, and Sears will repair it, free of charge.
- Page 3 SAFETY INSTRUCTmONS CONTINUED 11 ALWAYS WEAR EYE PROTECTION. Any Sander can throw foreign objects into the eyes which could cause permanent eye damage ALWAYS Wear Safety WEARYOUR Goggles (not glasses) that comply with ANSI safety standard Z87o t, Everyday eyeglasses have only impact-resistant lenses._ they ARE NOT...
- Page 4 SAFETY INSTRUCTIONS CONT/NUED [] ADDITIONAL SA!FETY INSTRUCTIONS FOR BELT/DISC SANDER OPERATE YOUR SANDER UNTIL IT IS COMPLETELY ASSEMBLED INSTALLED ACCORDING INSTRUCTIONS. I .THIS SANDER IS DESIGNED TO SAND 10 ALWAYS maintain a minimum clearance WOOD OR WOOD-LIKE PRODUCTS of 1/16 inch or less between tile table ONLY.
- Page 5 SAFETY INSTRUCTHO.NS CONTINUED l_ ADDITIONAL SAFETY RNSTRUCTIONS FOR BELT/DISC SANDER 20USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition When using an extension cord, be sure to use one heavy enough to carry the current your product will draw_ An undersized cord...
- Page 6 SAFETY INSTRUCTIONS CONTINUED m GROUNDING INSTRUCTIONS CONTINUED REPAIR OR REPLACE DAMAGED ONLY 3-WIRE EXTENSION CORDS THAT HAVE 3-PRONG GROUNDING VVORN CORD IMMEDIATELY...if repair or PLUGS 3-POLE RECEPTACLES replacement of the electric cord or plug THAT ACCEPT TOOL'S PLUG. ever necessary, connect equipment-grounding conductor...
- Page 7 TABLE OF CONTENTS SECTION PAGE Warranty............... Safety Instructions ..........Extension Cord Use ..........Specifications ............UnpacMng and Checking Contents ..... 8 Know Your Belt/Disc Sander ........ Assembly............. Fastening Sander to Work Surface ....... 11 Operation and Adjustment ........Maintenance ............
- Page 8 UNPACKING CHECKING CONTENTS _[ Tools needed assembly alignment: (see figure 1, Combination Square 2_Two hex keys (supplied) 3. Slotted and phillips screwdriver 4_Adjustable wrench Fig. I Bi Unpacking (see figure This belt disc/sander is shipped complete in one carton Carefiflly unpack the sander and all parts from the carton.
- Page 9 KNOW YOUR BELT/DmSC SANDER BELT TABLE Dust deflector BACKSTOP Sanding belt ---- Belt bed Sanding plate Sanding disc " Idler drum DISC TABLE --- Disc guard ON/OFF switch with Base mounting hole Fig. 3 KEY GUIDES FOR PROFESSIONAL RESULTS DISC TABLE: is used to support...
- Page 10 ASSEMBLY Installing sanding disc (see figure 1, Remove the two screws from the sanding disc guard and remove sanding disc guard plate. 2_Wipe sanding disc plate clean. 3, Peel backing from sanding disc, align disc with plate and press saxlding disc firmly on to plate, 4, Reinstall...
- Page 11 ASSENBL¥ CONTINUED Hounting the backstop (see figure l Align backstop with hole 2, Install lock washer and flat washer on screw 3 insert screw into backstop hole and tighten, Mounting the belt sander table (see figure 1, Insert washer on belt sander table fastening screv¢.
- Page 12 OPERATION ADJUSTMENTS t OFF switch (see figure l3) The keyed switch is hutended to prevent unauthorized use of the sander: 1•To mm sander "ON" insert the yellow key into the key slot in the center of the switch Z Push key firmly into the slot, then push switch to the r_,ht to start the sander.
- Page 13 CONTINUED OPEF T ON ADJUSTNENT$ Squaring the tables (see figure 17) lb ensure accurate end sanding the wade tables mt_ be sqtmre to the s_mding snarlhcesprior to using the tables for disc sanding, belt sanding, or vertiml belt sanding I Adjust tame you will be using to be 90" with the sanding sun'ace 2 Using a combination square, place one end on the table with the rifler end against the sanding surface, Check that the table is...
- Page 14 BASIC SANDING OPERATIONS CONTINUED Sanding inside curves (see figure 20) Sanding the inside curve of' the workpiece is done positioning the workpiece on the idler pulley of' the sanding belt, Hold workpiece firmly with both hands, Edge sanding of long workpieces (see figure 21 ) Adjust...
- Page 15 MAINTENANCE FOR YOUR SAFETY, TURN SWITCH "OFF" 3 Adjust the tension ot tlle belt by putting REMOVE THE POWER CORD FROM slotted screwdriver in the bracing sloE. THE ELECTRICAL OUTLET BEFORE Pushing up on the screwdriver will tighten the tension of the belt between ADJUSTING OR PERFORMING...
- Page 16 PARTS LIST MODEL NO. 39 i.226560 BELT/DISC SANDER Part Number Description Quan tit), Part Number Description Quantity 226560001 Knob 226560048 Base cover plate Drive belt 226560049 226560002 Spring base Screw fiat cross ?¢t5x14 226560003 Spring index 226560050 Washer countersink 226560004 22656005 226560005 Screw hex 6xl4mm...
- Page 17 73 74 Page I7...
- Page 18 /I:RRFTSMRN + r/DISC OWNER'S MANUAL Now that you have purchased your Belt/Disc Sander, should a need ever exist for repair parts or service, SERVICE simply contact any Sears Service Center and most Sears stores.. Be sttre to provide all pertinent facts when you ca_ or visit The model munber of yotu' Belt and Disc Sander MODEL NO.