Download Print this page

Craftsman 113.169240 Owner's Manual

Hide thumbs

Advertisement

r
Save This Manual
for Future
Reference
SEARS
owner's
manual
Model No.
113.169240
'
Serial
Number
Model and serial number may
be found on the back of the
bracket-handle.
You should
record both model and serial
number ina sere placefor future
use.
FOR YOUR
SAFETY
READ ALL
INSTRUCTIONS
CAREFULLY
I:RRFTSMRN
COMMERCIAL
DUTY
VAC CART
Fits Most 16 Gallon
Craftsman Wet Dry Vacs
• assembly
• operating
• repair parts
_,.
Seam,
Roebuck
and Co., Hoffman
Estates,
IL. 60179
U.S.A.
Part No. SP5389
Form No. SP5389-2
Printed in U.S,A.

Advertisement

   Summary of Contents for Craftsman 113.169240

  • Page 1

    You should record both model and serial number ina sere placefor future COMMERCIAL DUTY use. VAC CART Fits Most 16 Gallon FOR YOUR Craftsman Wet Dry Vacs SAFETY READ ALL • assembly INSTRUCTIONS • operating CAREFULLY • repair parts •...

  • Page 2: Table Of Contents

    Introduction This cart is designed especially for use with Craftsman 16 gallonWetJDryVacs only. For best results, be sure to fol- low these instructions. Table of Contents Section Page Section Page Introduction..............Tool Required ............3 Table of Contents ............2 Maintenance ..............

  • Page 3

    Pliers Phillips Screwdriver If any parts are missing or damaged, stop and contact your Authorized Service Center, Do not assemble until you have all the parts. 1. Turn the drum upside down on the floor with the drain facing you. 2.

  • Page 4: Assembly

    Assembly (continued) 9. Mount (1) retaining ring onto one end of axle. Using pliers,snap retaining ring intogroove on axle. Cradle Cradle 10. Slide wheel onto open end of axle. Left 11. Slide open end of axle thru cradle left and left leg, Righ_ making sure the leg slot lines up with the cradle hole.

  • Page 5: Plastic Handle Bracket

    S lide plastichandle bracket onto right and left legs. 17. Slide metal handle into (2) holes on plastic handle bracket. Metal Handle 18. Align holes in handle with hole in leg and plastichan- dle bracket. Plastic Handle Bracket 19. Install (2) #10 x 314 screws into (2) holes on legs with (2) matching holes on handle for each side.

  • Page 6: Maintenance

    Assembly (continued) 20. Locate (2) tabs on plastic handle bracket and position Tabs (2) slots on tote, Slide tote down over (2) tabs on bracket. Handle Bracket ToteJ Slots WARNING: To reduce the risk of injury: WARNING: To reduce the risk of back injury, falls or Before Each Use impact from falling vac: Limit the weight in the drum before lifting the vac or moving it up or down stairs.

  • Page 7: Right Leg

    Repair Parts Parts List for Vac Cart Model No. 113.169240 Always order by Part Number - Not by Key Number Pa_ No. Part No. Description Descrtption 819429 818438 Handle Caster 818434 818437 Bracket, Handle Cradle, Right 818436 818435 Left Leg Right Leg 806742-5 ,_LScrew TY AB #10 x 3/4...

  • Page 8

    SEARS COMMERCIAL DUTY VAC CART owner's manual Fortke repair or replecementparisyouneed Model No. (;all7 am - 7 pm, 7 daysa week 113.169240, 1-800-366-PAITT (1-800-360-7278) Forin-homemajorbrandrepair service Call24 hoursa day,7 daysa week 1-800-4-REPAIR (1-800-473-7247) The model number of yourCom- mercial Duty Vac Cart will be found on the back of the handle bracket.

Comments to this Manuals

Symbols: 0
Latest comments: