Cutter Guard; Starting Pin; Removing And Installing Cutters - Sears 113.239201 Owner's Manual

Wood shaper
Hide thumbs Also See for 113.239201:
Table of Contents

Advertisement

c. TO lock switchin OFFposition..,holdswitchIN
withone hand.,
. REMOVE key with other hand,
ALWAYS
LOCK
THE
SWITCH
"OFF"
WHEN
SHAPER
IS NOT IN USE...
REMOVE
KEY AND
KEEP IT IN A SAFE PLACE,,.
ALSO...
tN THE
EVENT
OF A POWER FAILURE
(ALL
OF YOUR
LIGHTS GO OUT) TURN SWITCH OFF .,, LOCK IT
AND
REMOVE
THE KEY.
THIS WILL
PREVENT
THE SHAPER FROM STARTING
UP AGAIN WHEN
THE POWER COMES BACK ON,
2,
ELEVATING
CONTROL
LEVER
The
Elevating
Control
Lever
moves
the
spindle
vertically
a distance of 7/8-inch
to locate the cutter
at
the desired vertical
position.
3.
SPINDLE
LOCK
KNOB
-
used to lock the spindle and
quill
assembly
after
the
desired
height
has
been
determined.
CAUTION:
Always
release
the quill
lock
knob
before
attempting
to
change
the
position
of
spindle
and
tighten
the knob securely before starting operation.
4.
SPINDLE
-
This
shaper
is designed
for
use
with
maximum
2-1/2-inch
diameter
cutters
having
a 1/2-inch
diameter
bore.
5.
SPACERS
-
A total
of three spacers are provided,
two
7/16
inch thick
and one 1/4 inch
think
for positioning
the cutter
for desired shapes.
6.
KEYED
WASHER
-
Must
always
be
positioned
immediately
below the spindle
nut.
7.
FENCE
ADJUSTING
KNOB
-
Each fence face may be
moved
forward
or
backward
by
turning
the
fence
adjusting
knobs.
8.
FENCE
LOCK
KNOB
-
After
the desired
fence
face
position
has
been
selected,
the
fence
is secured
by
tightening
the fence lock knobs.
9.
FENCE
FACES
-
Each fence
may be moved
forward
or
backward
by
releasing
the
fence
lock
knob
and
turning
the
fence
adjusting
knobs.
Each
fence
face
operates
independently
of the other,
by means of the
adjusting
mechanism.
After
the desired
fence
position
has been
selected,
it is secured
by tightening
the fence
lock
knob.
The
fence
faces
wilt
close
in
from
a
maximum
three-inch
opening
down
to
one-inch
for
small
diameter
cutters,
by loosening
the two
screws in
the front
of each face and sliding
the face to the desired
posiiton.
The screws
must
be tightened
securely
after
each setting.
CAUTION:
The opening between inner ends of fence faces
should never be larger than required to just clear the
particular cutter
being used. ALWAYS
ROTATE
THE
SPINDLE BY HAND BEFORE STARTING
THE SHAPER
MOTOR TO MAKE SURE CUTTER
DOES NOT STRIKE
FENCE FACES.
10. CUTTER
GUARD
NOTE:
Used
for
curved
or
irregular
shaping
only-
fence
must
be removed
and
starting
pin
must
be in
place on in-feed
side.
11.
12.
Provides
added protection
for
irregular
shaping.
Guard
is adjustable
for various
thickness
of material.
CAUTION:
Always
rotate
the
spindle
by hand
before
starting the shaper motor to make sure cutter does not
strike guard.
STARTING
PIN
The Starting
Pin must
be used as a pivot to support
the
work
until
it
has been fed into
the cutter
and against
the collar.
The Starting
Pin may be located
in either
of
the two
threaded
holes near
the table
insert
opening,
depending
upon
the
direction
of
rotation,
but
ALWAYS
on the in-feed
side.
REMOVING
AND
INSTALLING
CUTTERS
a.
Raise spindle
to maximum
height
b.
To REMOVE
cutter,
hold
spindle
with
the t/4"
hex
wrench
and loosen
nut
with
wrench
provided
as
shown
-- Reverse procedure
to TIGHTEN
SPINDLE
NUT.
NOTE:
TO
AVOID
POSSIBLE
BENDING
OF
THE
SPINDLE
LOOSEN
OR TIGHTEN
NUT
WITH
BOTH
WRENCHES
POINTING
AS NEARLY
tN THE SAME
DIRECTION
AS POSSIBLE.
CAUTION:
Always
have
the
keyed
washer
directly
under
the
nut,
otherwise
the
nut
may
loosen
and
serious injury could result.
1/'4
IN,
HEX
WRENCH
\
LOOSE
N
/
t/
TI GHTE N
WRONG
R_GHT
,!,,
13

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Craftsman 113.239390Craftsman 113.239201

Table of Contents