Table of Contents
Advertisement
.....
n ......... f ..... "n........... " .....
add=tBo al sa sty
structaons for jointer-planer
Safety is!a combination ofcommon sense, staying alert
and knowing flow your jointer-pianer works_ .....
BEFORE
EACH USE:
1. Inspect your jointer-pfaner.
BEFORE
USING THE JOINTER-PLANER:
WARNING: TO
AVOID MISTAKES
THAT COULD
CAUSE SERIOUS, PERMANENT
INJURY, DO NOT
PLUG THE JOINTER-PLANER
IN UNTIL THE FOL-
LOWING
STEPS
HAVE BEEN
SATISFACTORILY
COMPLETED.
1. Assembly and alignment.
2. Learn the function and proper use of the on-off
switch, fence slide locking handle, cutter guard,
depth of cut hand wheel, locks and stops, fence
bevel lock handle, ouffeed table, infeed table and
hold-down/push-blocks.
3. Read and understand all safety instructions
and
operating procedures throughout the manual.
4. Read the following
labels which appear on the
jointer-planer:
WARNING
THESTARTING RELAY IN THIS
JOINTER IS AGRAVITY
SENSmVE
TYPE. NEVER T URN THE POWER
ON UNTILTHE JOINTER HAS
BEEN MOUNTED
ON THE LEG SET
AND ISINUPRIGHT
POSITION.
r
JlDANGER|
FOR YOUR OWN SAFETY: KnowThis Tool!
Read and Understand
the Owner's
Manual
Befo= _ Using Machine_
WARNING: THE 2-INCH JOINTER-PLANER
PULLEY
AND THE 2-1/2 INCH MOTOR PULLEY FURNISHED
WILL RUNTHE CUTTER HEAD AT ABOUT 4300 RPM
WHEN USED WITH A 3450 RPM MOTOR. USE OF
DIFFERENT
TYPES
OF PULLEYS
OR MOTORS
WILL CHANGE THIS SPEED AND COULD CAUSE
JAMMING,
BINDING,
KICKBACK,
THROWN
BLADES OR OTHER DANGERS.
a. If any part of this jointer-p_aner is missing, or bent,
or has failed in any way, or any electrical parts
don't work properly, turn the jointer-planer off and
unplug the jointer-planer. Replace damaged, mis-
sing, or failed parts before using the jointer-planer
again.
b. Make sure the cutter head turns in the right direc-
tion. The top should move toward the infeed table.
Call your Sears Service Department for help if
the cutter head turns the wrong way.
c. Make sure the cutter guard works properly. With
the switch off and key removed, pull the cutter
guard open and let go. If the guard doesn't
smoothly swing closed, contact Sears Service,
d. Keep blades sharp. Dull or knicked blades tend
to "pound"
and chew at the wood, causing
kickbacks.
e. To avoid injury from thrown pieces, make sure
the blades are properly installed and the cutter
blade wedge, screws are tight.
2. Plan Your Work to protect your eyes, hands, face,
ears.
....
• Wear Safety Gogg]es complying
with ANSI Z87,1.
S Always
Use Cutter
Head Gua,d.
Make sure it springs
shut automaticaily:
_
:
:
a_.
Bef0re trying a new or fittte used operation,
care-
,
AIways=se_,iveg.=d.
_i ::: : ,: ::i
;:
fully pianyour
hand placement. Make sure you
• Use HoldlDown
Push Blocks
for:
:
,
: :: :
_: Jointlngmsteri,l
narrower
than
3 inches
or
....
:
....
_
have proper
hold-down/push-blocks,
jigs, fix-
P_.tng,.a_r_,_thi.,,.,tha. __n=,_s. :_:
_ _ :_ :
:
'
tures,.stops, etc. ready to use.
!n=h.:
i
i : i:
:
Do layout, assembly or set up work on the tabte
_
......
_: : : ':i_ i'"
only while the jointer-planer is off and the switch
WHEN INSTALLING _OR MOVING THE
key
removed.
JOINTER-PLANER:
_ ,
c.
11 To avoid injury:fromltmexpected jOinter-planer or
workpiece imovement;. ;
i:
.....
:i::
C;
d.
e,
a. Use the jointer-ptaner indoors °na firm level sur-
face in a well lit area,
b. Place the jointer-planer where:
i. there is plenty of room for moving the work-
piece through the entire cut.
ii. no one must stand in line with the wood while
planing or jointing it.
Adjust the jointer-planer
so the tables are level
and the jointer-ptaner does not rock.
Turn off and unplug the jointer-planer before mov-
ing it to a new area. To avoid back injury, get help
when you need to tift the jointer-planer.
Bolt the jointer-planer
to the floor if it tends to
slip, walk, slide or tip over during work like cutting
long, heavy boards.
3
Wear safety goggles (not glasses) that comply
with ANSI Z87.1 (shown on package). Using any
power tool can result in foreign objects being
thrown into the eyes, which can result in perma-
nent eye damage. Safety goggles are available
at Sears retail catalog stores. Use of glasses or
use of goggles not in compliance with ANSI Z87.t
could result in severe injury from breakage of the
eye protection.
WEAR
YOUR
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
