Table of Contents
Advertisement
Messages
The following messages or service numbers appear on the TV or unit's display when something unusual is detected during startup and use.
On the TV
Page
Cannot
play.
oYou inserted an incompatible
disc (Discs recorded in PAL video, etc.).
42, 43
Cannot
display
on this unit.
oYou tried to play a non-compatible
image.
43, 44
oConfirm
"SD" on the unit's display is not blinking and re-insert the card.
No disc is inserted,
oThe disc may be upside down.
Q This operation
is not
oSome operations are prohibited by the unit or disc. For example;
available.
- r¢l_'_: During play back, reverse slow-motion
or reverse frame-by-frame
is not possible.
Q This operation
is prohibited
oDepending
on the disc, you may not be able to perform search or skip when film previews
by this disc.
and warning screens are being played back.
Cannot
connect,
oWhen a hub is used but its Link lamp does not light up, check the cable connection,
LAN
14
Please check the connection
of
terminal connection, cable itself (a cross cable may be used by mistake), etc.
the LAN cable.
IP address is not set.
33
Cannot
obtain IP address using
DHCP.
Please check the connection
or
router settings.
This IP address
is already in
use.
Please check the IP address
setting.
Unable to perform Connection
Test.
Please try again.
IP address
not set correctly.
Connection
Test was
unsuccessful.
No reply
from host.
Please check the connection
or
router settings.
oThe "IP Address" in "IP Address/DNS
Settings" is"
.
.
.
". Set the "IP Address",
"Subnet Mask", and "Default Gateway". (Select the automatic address acquisition
if
necessary.)
olf you use a hub, then check the connection between the hub and the router.
- Use the UPLINK port of the hub to connect to a router.
-Check
whether or not the hub's Link lamp lights up. If it does not light up, then check the
cable connection, LAN terminal connection, cable itself (a cross cable may be used by
mistake), etc.
• If the above conditions are OK, then the router may not operate in DHCP mode. Check the
router settings and operation. You may reset the router to restore it to normal.
• This unit's IP address is used by another device. Check the IP addresses of this unit,
personal computers,
and routers, etc. If necessary, reconfigure them to avoid IP
addresses from being duplicated.
Turn the unit off. Remove the power cord and reconnect it and try again. If the same
symptom persists, then consult your dealer.
• If you use a hub, then check the connection between the hub and the router.
- Use the UPLINK port of the hub to connect to a router.
- If the hub's Link lamp does not light up, then check the cable connection,
LAN terminal
connection, cable itself (a cross cable may be used by mistake), etc.
• Check the "IP Address", "Subnet Mask", and "Default Gateway" in the "IP Address/DNS
Settings".
• If the MAC address information
is required, then press [SETU P] to display the "Network"
menu.
14
14
14
33
33
37
Network connection
refused.
•When you set "BD-Live Internet Access" to "Allow ( Limited )" and play BD-Live contents
Please confirm
Setup "BD-Live
which do not have a content owner certificate, the Internet access of the content is not
Internet
Access."
allowed. If you allow the content to connect to Internet, set "BD-Live Internet Access" to
"Allow ( ALL )'.
Unable to check for latest
•The firmware download server is currently unavailable.
Please try again later.
firmware
version.
Please try again later.
High Clarity Sound
is effective.
•"High
Clarity Sound" in setup menu is set to "Enable", and "High Clarity Sound" in
36, 38
Analog
video output
is turned
on-screen menu is set to "On".
off when
playback
starts.
No Video
•Depending
on the connected
iPod, video menu may not be available on the TV. Select the
31
iPod menu (iPod LCD) mode and operate video playback from your iPod menu.
On the unit's display
F99
•The
unit fails to operate properly. Press [POWER (b/I] on the main unit to switch the unit to
--
standby for 3 seconds. Now press [POWER (b/I] on the main unit again to turn the unit on.
HDMI ONLY
•Some
BD-Video discs can only be output with HDMI.
--
NET
•Displays
while VIERA CAST is starting up.
--
No PLAY
•There
is a viewing restriction on a BD-Video or DVD-Video.
37
No READ
•The
media is dirty or badly scratched.
The unit cannot play.
--
PLEASE WAIT
•The
unit is carrying out internal process.This
is not a malfunction. You cannot operate the
unit while "PLEASE WAIT" is displayed.
• When connected
to TV (VIERA) with HDAVI Control 4, and power supply is turned off by
the "Auto power stand-by" function on the TV side.
SET []
•The
remote control and main unit are using different codes. Change the code on the
50
(" []"
stands
for a number.)
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
UNFORMAT
•You inserted an unformatted
DVD-RAM,
DVD-RW, +RW, an unused +R, +R DL or
--
DVD-RW (DVD-Video format).
UNSUPPORT
•You have inserted a media the unit cannot play.
42, 43
RQT9371
Hide quick links:
Advertisement
Table of Contents
