Hint For Timer Recording; Copying A Video Tape - Emerson EWD2004 Owner's Manual

Hint for Timer Recording

• If there is a power failure or the DVD/VCR has been unplugged for more than 30 seconds, the clock setting
and all timer settings will be lost.
• If a tape is not in the DVD/VCR or does not have the record tab, the TIMER REC light flashes and timer
recording cannot be performed. Please insert a recordable tape.
• If a tape ends during timer recording, the VCR will stop, eject the tape and switch to the DVD mode automati-
cally as the TIMER REC light flashes. (If the DVD power is off, the VCR will become STANDBY status.)
• When all timer recordings are finished, the TIMER REC light will flash.
• When timer recordings are set, the TIMER REC light will appear. To use the VCR as usual until the time
for the recording, press the SUBTITLE/T-SET button so that the TIMER REC light disappears. Press the
VCR/TV button to choose the VCR position. Select either VCR or DVD mode, then continue with the
other features as described in this manual.
If you want to use the DVD player during a VCR timer recording or while the TIMER REC light is on or
flashes.
• You can use the DVD player while the TIMER REC light is on or flashes, or during a timer recording. Press
the POWER button to turn on the DVD. Press the DVD button on the remote control to choose DVD mode,
then continue with the other DVD features as described in this manual. You don't have to set the TIMER off to
use the DVD only.

Copying a Video Tape

Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
(Back of another source)
1
DVD/VCR VCR
or
COMPONENT
AUDIO OUT AUDIO IN
VIDEO OUT
AUDIO OUT ANT-IN
Y L L AUDIO OUT
Connect
C B R R
VIDEO OUT VIDEO OUT VIDEO IN ANT-OUT
C
R
Audio/Video cables
(not supplied)
Hint
Hint
• For best results during dubbing, use the front panel controls whenever
possible. The remote control might affect another source's operation.
• Always use video-quality shielded cables with RCA-type connectors.
Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver or other audio/video
component with A/V outputs.
• "L1" or "L2" is found before the lowest memorized channel. (Example:
CH02)
• "L2" input jacks are on the front of this DVD/VCR.
(Back of Recording DVD/VCR*)
2
DVD DVD/VCR VCR
DIGITAL AUDIO S-VIDEO COMPONENT AUDIO OUT
Connect
VIDEO OUT
OUT OUT ANT-IN
Y L
AUDIO IN
L
C B R R
COAXIAL
R VIDEO OUT VIDEO IN ANT-OUT
C
R
RF cable
(supplied)
*Front input jacks are also available
1) Insert a pre-recorded tape into the playing VCR.
(Back of TV)
2) Insert a tape with its record tab into the recording
DVD/VCR.
3) Press the SPEED button on the remote control
of the recording DVD/VCR to select the desired
recording speed (SP/SLP).
4) Select the "L1" or "L2" position on the recording
DVD/VCR.
• To use the input jacks on the back of this unit,
select "L1" position by pressing [0], [0], [1] on
the remote control or the CHANNEL buttons.
• To use the input jacks on the front of this unit,
select "L2" position by pressing [0], [0], [2] on
the remote control or the CHANNEL buttons.
5) Press the REC/OTR button on the recording
DVD/VCR.
6) Begin playback of the tape in another source.
7) To stop recording, press the STOP/EJECT button
on the recording DVD/VCR, then stop playback of
the tape in another source.
– 13 – EN